11-27-2018, 06:25 AM | #1 |
Join Date: Nov 2018
Location: gin gin qld australia
Posts: 3
|
chinese quads
hi everyone..
well I live in qld in Australia so temp range 20c to 40c 70f to 110f elevation above sea level around 300metres plus..so 900ftplus I got 3 x 250cc quads 2 x zongshen water cooled ..I think 1 is 300cc 1 x shineray air cooled ok all have clone carbi pz30... I got a brand new kt pz30 no pilot markings no main markings... the mystery carbi... 3 of the rest jingke with 36 36 39 pilots...and 105 105 105 mains.. ok here the story....quad 1 2002 model 250cc zongshen with jingke...carbi....been sitting doin nothing for 2 years quad 2 2014 model zongshen 300cc with jingke carbi....been sitting doing nothing for 2 years also... quad 3 ;;;;2017 been sitting for 9months...jingke carbi shinray air cooled.. cleaned tanks and all quads carbi...new fuel lines quad 3 2017 starting playing up..unstable idle...stalling...revs where ok choke start when cold ok hot start ok..reved ok but idle was way high over 1400rpm...had dangerous twist throttle ..so I converted it back to thumb...wanted the revs down ...you could tke off without any throttle at all...that's how I got it set hi.. so I recleaned its carbi again...tank fuel lines filter.. must have the mixture turns wrong .. could not get it start ...so I tried the new one kt...with its factory set... it wouldn't start it...either... here is where I opted to clean and try the 2 other quads carbis.. they didn't work either... and to my amazement althought jetted simular....as I wrote above...36 36 39 105 105 105 ...all had different mix setting.. strange because all 3 engines are simular clones of cg250... 2 x167mm fm 1x 176nm I figure if I get carbi to work on quad 3 shineray 250....and all to work on her....they all good to go back on quad 1 and 2... quad 1 and 2 also had too high idle always as well...1 was cranky starter..but both reved good ... I not checked all quads notch setting for piston needle yet... no 3 quad I have ...its 2nd notch from bottom...think its got 5 or 6 notches heres the plan...clean all tanks and lines filters carbis.. start with quad 3 ...check manifolds gaskets..etc.. find a carbi out of bunch that will easy start and hold idle stable and close to 1400rpm hopefully I get all doin it and I don't care what mixture seting start off being then try get it to do that ...but allow reving as well see how many will... those that don't I try differing jetting I figure surely a working quad 3 carbi...should be ok on quad 1 or 2 as well that's the plan....if anyone has any ideas...or settings to try...let me know ok...ty phil |
|
11-28-2018, 09:38 AM | #2 |
Join Date: Nov 2018
Location: gin gin qld australia
Posts: 3
|
update
fixed scews on 1 carbi
got new carbi nuts too stay tuned... I do some photos as well....could be helpful ok gang bye
__________________
1 zongshen motor bike 250cc 1 zongshen quad 250cc 1 zongshen quad 300cc 1 shineray quad 250cc |
|
12-30-2018, 07:57 PM | #3 |
Join Date: Oct 2017
Location: shelton, Washington
Posts: 167
|
Help us so we can help u. Different settfor different .others isn't unusual. Some have more er.... were that others. One motor at at a time please.
__________________
2006 roketa 200cc 1971 Yamaha xs650 2x 1980 xs650, 1 is a café, other is a chopper/brat 1972 Honda xl250 2x early 90's Honda rf600 parts bikes more mc junk laying around. |
|
|
|
|
|