![]() |
#1 |
Join Date: Nov 2015
Posts: 19
|
Actual seat height for RX3?
I was doing some more research on the bike and it looks like the last question i have is what the actual seat height is. A lot of sources seem to quote 31.3" but that was when there was a 15" wheel still coming standard. Now with the standard 17" rear, I'm wondering if the seat height has gone up much higher. Also curious how much more a 19" front would raise it.
I'm very close to pre-ordering a 2016, but just making sure I'm 100% sure what I'm getting into. |
![]() |
![]() |
#2 |
Join Date: Dec 2015
Posts: 200
|
Also interested in this info as I haven't decided to buy yet.
|
![]() |
![]() |
#3 |
Join Date: Sep 2014
Posts: 247
|
The seat height is 31.3 inches. The 17-inch rear wheel and tire is actually very slightly smaller in diameter than the Asian-configuration 15-inch diameter wheel and tire due to the 17-inch rear tire's smaller sidewall.
|
![]() |
![]() |
#4 |
Join Date: Nov 2015
Posts: 19
|
thanks!
|
![]() |
![]() |
#5 |
Join Date: Oct 2015
Location: FL, GA, NC
Posts: 771
|
I measured the seat height on my RX3 with a level across the seat at its lowest point.
It was 32". jb
__________________
2016 Honda CB500F......2017 Triumph Street Twin 2014 XT 250........ |
![]() |
![]() |
#6 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
![]() ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
![]() |
![]() |
#7 | |
Join Date: Oct 2015
Location: FL, GA, NC
Posts: 771
|
Quote:
I have installed a lowering link, but haven't measured the actual new height. I'm away from home for the holidays. Will be able to measure again next week. The rider "sag" is only 3/4" (180#). I think I need to play with the rear shock preload when I have the bike apart for the valve check. That may affect the seat height. jb
__________________
2016 Honda CB500F......2017 Triumph Street Twin 2014 XT 250........ |
|
![]() |
![]() |
#8 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
I haven't measured the saddle height on my bike, because it doesn't cause me any problems.
![]() I think someone else here has measured the saddle height, both with the stock saddle, and one of the aftermarket saddles. ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
![]() |
![]() |
#9 |
Join Date: Oct 2015
Location: FL, GA, NC
Posts: 771
|
__________________
2016 Honda CB500F......2017 Triumph Street Twin 2014 XT 250........ |
![]() |
![]() |
#10 |
Join Date: Feb 2016
Location: Western, CT
Posts: 168
|
Seat Concepts Narrow Seat
Does anyone have any experience with how much additional reach would be provided with the Seat Concepts Narrow seat? Ordered one and I have a 29" inseam - hoping it will do the trick as 32" standard will be tough for me to get the balls of my feet down.
Last edited by Dualsport Chic; 02-07-2016 at 10:52 PM. |
![]() |
![]() |
#11 |
Join Date: May 2006
Location: Yuma, Arizona
Posts: 9,035
|
I have a TMEC 200 and my seat is 33.5". I am 5'7" and about 30" inseam, and can get both feet down, although not completely flat-footed. Granted the CSC bike might be a little larger, but I am guessing the RX3 will be fine for you.
__________________
"They say that life's a carousel, spinning fast you got to ride it well..." TGB Delivery Scooter 150 TMEC 200 Enduro--carcass is sadly rotting in the backyard |
![]() |
![]() |
#12 | |
Join Date: Jul 2015
Location: Milpitas, CA. USA
Posts: 775
|
Quote:
I think she may have some good input for you, Dualsport. |
|
![]() |
![]() |
#13 |
Join Date: Feb 2016
Location: Western, CT
Posts: 168
|
Thank you Jay - Woodland Sprite is a former TWF (TwoWheelFemales) member - we were on the forum together for several years prior to it shutting down this past summer. Will be great to get her impressions of the bike!
|
![]() |
![]() |
#14 | |
Join Date: Oct 2015
Location: FL, GA, NC
Posts: 771
|
Quote:
I didn't find it any lower than the stock seat...but maybe more comfortable....but they have had it so long, I have forgotten what it felt like. jb
__________________
2016 Honda CB500F......2017 Triumph Street Twin 2014 XT 250........ |
|
![]() |
![]() |
#15 |
Join Date: Jun 2015
Location: Parker, Colorado
Posts: 40
|
Not sure the narrow seat will help much. Detours has one and he was kind enough to let me test sit on his motorcycle. I didn't notice much if any difference. I have the lowering link, a shaved down stock seat, and a 29" inseam...can barely get the balls of my feet on the ground.
__________________
Our collection: Mark - KLR650, TT250, RX3 Marlissa - RX3, XR100 |
![]() |
|
![]() |
![]() |
|
|