|
![]() |
|
![]() |
|
Thread Tools | Search this Thread | Display Modes |
|
![]() |
#1 |
Join Date: Jul 2013
Location: Türkiye
Posts: 88
|
ZS177MM / NC250 Clutch crossreference = Honda dominator 650 , NX 650 EBC CK1170 series dimensions bit tight tolarance 0.01-2mm , same, i used that on my ZS177MM / NC250 confirmed
Note : originals better , only use if cant find original clutchs, just instead exigency (on travel need repair or...) |
![]() |
![]() |
#2 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
![]() I always suspected the RX3 clutch parts were Honda parts. ![]() Honda XR650L Honda XR600R Honda NX650 Honda CR500R Honda CR480R Honda CR250R A lot of people like the Tusk Clutch Kits you can purchase from Rocky Mountain ATV/MC. ![]() https://www.rockymountainatvmc.com/p...ch-Kit?v=11638 ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
![]() |
![]() |
#3 | |
Join Date: Jul 2013
Location: Türkiye
Posts: 88
|
Quote:
Here my old acc, on forum mt, search and dimensions maybe have idea, again http://www.motosiklet.net/forum/mt-a...-tip-uyum.html EBC CK 1170 clutch's is very tight tolarance but ok worked. |
|
![]() |
![]() |
#4 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
When I have time, I will also check the dimensions of the clutch plates in my Honda CRF250X.
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
![]() |
![]() |
#5 | |
Join Date: Jul 2013
Location: Türkiye
Posts: 88
|
Quote:
![]() Organic/Fiber plate is ok , butif u add link on photos metal friction metal plates impossible, not need measured, many time i assemb/dissasemb clutch , if photo correct any a optical game " F " optic playing idk, but im think on photos that metal discs impossible mounted rx3 or zs177 or nc250 Measured sorry, motor block is complete , but if wait me 2-3 day later maybe, i promise. 116 mm ( in chamber , non tooth.) , 9 mm(in circle to out walls non toth) , 136 mm (out chamber) Dimensions of the metal plate. Edit for measurement for Spud, bestregards. Sorry bad Photos by sj1000 (because my suck xperia u phone probably today REGL/menstruation , %+&%+/% waste phone never buy.) Nx 650 dominator Fiber/organic idk, clutchs on my zs177mm, i used it 500 kilometer than, non problem, just mounted very tight tolaration, thick but worked i cant feel any problem it worked. Edit 2 sj1000 need setup for date and watch. , photos is fresh 10 min ago. ![]() ![]() ![]() Last edited by Co2; 11-19-2015 at 02:52 PM. |
|
![]() |
|
![]() |
![]() |
|
|