03-06-2015, 09:54 PM | #1 |
Join Date: Mar 2015
Posts: 3
|
Gy200 engine parts- Valves
I have a green redcat gy200 and in need of valves. My intake is bent with only 60 miles. I can't seem to find any. Does anyone know where I can source them?
Thanks in advance for any suggestions |
|
03-06-2015, 11:27 PM | #2 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Thanks for starting the new thread. I'm sorry I missed your PMs, my mailbox was full. I needed to delete a few old messages.
If you post photographs of both sides of your engine, we can verify the model. Then I'm sure someone will offer a good suggestion to help you find a new valve.
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
03-07-2015, 02:16 AM | #3 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Welcome!
As Spud says, pictures will help.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
03-07-2015, 08:44 AM | #4 |
Join Date: Mar 2008
Posts: 2,436
|
Measure it 1st, some brand can't use the mainstream CG200 parts...
"Individual" chinese bike mechanic likes these quality brand : 正洲 (VTC) -Taiwanese brand that made locally / 大东 (DDQM) -Based in Chongqing , many bike's stock valves are supplied by them... Parts supplier in Guangzhou DDQM : http://item.taobao.com/item.htm?id=38679462803 Generic: http://item.taobao.com/item.htm?id=38516771834
__________________
|
|
03-07-2015, 11:01 AM | #5 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
I didn't know that! Thanks for your terrific info as always, HB!
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
03-07-2015, 01:15 PM | #6 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
X2; thank you, Humanbeing.
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
03-08-2015, 07:54 AM | #7 |
Join Date: Mar 2008
Posts: 2,436
|
Mainstream CG200 are like this http://item.taobao.com/item.htm?id=14516420402
__________________
|
|
03-08-2015, 09:30 AM | #8 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
I didn't realize that CB valves were that much larger than CG valves.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
03-10-2015, 07:56 PM | #9 |
Join Date: Mar 2015
Posts: 3
|
Gy200 redcat
Here it is, anyone know what replacement valves I need?
Thanks |
|
03-10-2015, 11:06 PM | #10 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
That's definitely a CG. Can you measure the valves?
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
06-23-2015, 10:02 PM | #11 |
Join Date: Mar 2015
Posts: 3
|
It runs!
I was able to find a valve that fit but had to take it to a machinist to move the keeper groove further down the shaft. Is there anything I should do as it still isn't broken in yet? My mech set the timing, so should that prevent another bent valve? he said that the valve could have been stuck open from sitting too long.
|
|
|
|
|
|