Front wheel bearing change ?'s

yellowxj · 04-11-2011, 08:32 PM

Went to put my new front tire on and found that I have some bad front bearings...any directions on line to change them? 6301RS or 6301-2RS are the part numbers I found. Any numbers that the local parts houses woud recognize?

Its on my 2006 Lifan 200gy5 enduro..thanks all.

Weldangrind · 04-11-2011, 10:23 PM

Your local bearing shop will match them easily, and offer a sealed bearing.

yellowxj · 04-11-2011, 11:02 PM

I pulled the front tire off but didnt see how to press the old ones out? Gotta reach through with a punch?

FastDoc · 04-11-2011, 11:18 PM

Quote:

Originally Posted by yellowxj

I pulled the front tire off but didnt see how to press the old ones out? Gotta reach through with a punch?

Yup.

Check out www.dansmc.com.

Weldangrind · 04-12-2011, 12:41 AM

There might be a tube spacer between the two bearings, and they might also have a shoulder that they bottom against. After you've pounded one bearing out, make sure that you're hitting the second bearing and not the shoulder.

I bought a bearing installer at Princess Auto (Harbor Freight should have one for cheap), and it protects the bearing and gives you a handle to work with. It comes with several different sizes, so it's also good for trailers and cars.

Weldangrind · 04-12-2011, 12:43 AM

Sorry, should have said bearing and seal installer. It's the best way to install a bearing or a seal.

Here's one: http://www.harborfreight.com/10-piec...set-95853.html

SpudRider · 04-12-2011, 03:03 AM

Quote:

Originally Posted by Weldangrind

Sorry, should have said bearing and seal installer. It's the best way to install a bearing or a seal.

Here's one: http://www.harborfreight.com/10-piec...set-95853.html

Yikes! That driver set is much more expensive than I had anticipated! 8O I just place one of the the old bearings on top of the new one, and tap the bearing home with a hammer.

Place the new bearings in a plastic bag, and place the bag in your freezer for a few hours before you install the bearings. The cold bearings shrink a bit, making them easier to install.

After the bearings thaw, they expand a bit, making a tight fit.

Spud

Weldangrind · 04-12-2011, 10:09 AM

There is a 20% off coupon in Hot Rod (any many other mags) each month, and it is likley available for download. The seal / driver tool I bought was probably around $10.00 on sale.

FastDoc · 04-12-2011, 11:27 AM

Quote:

Originally Posted by SpudRider

Quote:

Originally Posted by Weldangrind

Sorry, should have said bearing and seal installer. It's the best way to install a bearing or a seal.

Here's one: http://www.harborfreight.com/10-piec...set-95853.html

Yikes! That driver set is much more expensive than I had anticipated! 8O I just place one of the the old bearings on top of the new one, and tap the bearing home with a hammer.

Place the new bearings in a plastic bag, and place the bag in your freezer for a few hours before you install the bearings. The cold bearings shrink a bit, making them easier to install.

After the bearings thaw, they expand a bit, making a tight fit.

Spud

I learned that trick from Brother Dan!

yellowxj · 04-12-2011, 07:23 PM

I appreciate all the help BUT my wife sold my $500 bike for $700 today as it was.

It was getting hard to ride with me 6' 260lb and my 84lb-ish kids so its time for me to get something bigger. It was fun. The kid that bought it asked my wife where the down shift "button" was 8O somethings they dont teach you in class. Atleast its a manageable bike to learn on.

FastDoc · 04-12-2011, 07:27 PM

Good news! Sometimees we make a little $ on resale. That's the advantage to buying chep and selling cheap.

Maybe you need a Pitster Pro 400? 8)

katoranger · 04-12-2011, 07:53 PM

You're tall enough for a KLR650. They have no problem 2up.

http://atlanta.craigslist.org/nat/mcy/2257507135.html

FastDoc · 04-12-2011, 08:12 PM

Roger (250 lbs) and I (175 lbs) and about 40 lbs of gear rode his KLR to Odessa (100 miles) last week no trouble. 8)

I'm not saying we didn't look silly though. :wink:

yellowxj · 04-12-2011, 08:56 PM

http://gainesville.craigslist.org/mcy/2319176628.html this ones close to me...carbs cleaned? any way to make sure thats all it needs? I'll email and see if they still have it.

yellowxj · 04-12-2011, 09:07 PM

or this one isnt too far away just to flip it.

http://jacksonville.craigslist.org/mcy/2313754490.html

04-11-2011, 08:32 PM	#1
yellowxj Join Date: Apr 2008 Posts: 79	Front wheel bearing change ?'s Went to put my new front tire on and found that I have some bad front bearings...any directions on line to change them? 6301RS or 6301-2RS are the part numbers I found. Any numbers that the local parts houses woud recognize? Its on my 2006 Lifan 200gy5 enduro..thanks all.
	0

04-11-2011, 10:23 PM	#2
Weldangrind Join Date: Mar 2009 Location: Sardis, BC, Canada Posts: 25,977	Your local bearing shop will match them easily, and offer a sealed bearing. __________________ Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer
	0

04-12-2011, 12:41 AM	#5
Weldangrind Join Date: Mar 2009 Location: Sardis, BC, Canada Posts: 25,977	There might be a tube spacer between the two bearings, and they might also have a shoulder that they bottom against. After you've pounded one bearing out, make sure that you're hitting the second bearing and not the shoulder. I bought a bearing installer at Princess Auto (Harbor Freight should have one for cheap), and it protects the bearing and gives you a handle to work with. It comes with several different sizes, so it's also good for trailers and cars. __________________ Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer
	0

04-12-2011, 12:43 AM	#6
Weldangrind Join Date: Mar 2009 Location: Sardis, BC, Canada Posts: 25,977	Sorry, should have said bearing and seal installer. It's the best way to install a bearing or a seal. Here's one: http://www.harborfreight.com/10-piec...set-95853.html __________________ Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer
	0

04-12-2011, 10:09 AM	#8
Weldangrind Join Date: Mar 2009 Location: Sardis, BC, Canada Posts: 25,977	There is a 20% off coupon in Hot Rod (any many other mags) each month, and it is likley available for download. The seal / driver tool I bought was probably around $10.00 on sale. __________________ Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer
	0

04-11-2011, 11:02 PM	#3
yellowxj Join Date: Apr 2008 Posts: 79	I pulled the front tire off but didnt see how to press the old ones out? Gotta reach through with a punch?
	0

04-12-2011, 07:23 PM	#10
yellowxj Join Date: Apr 2008 Posts: 79	I appreciate all the help BUT my wife sold my $500 bike for $700 today as it was. It was getting hard to ride with me 6' 260lb and my 84lb-ish kids so its time for me to get something bigger. It was fun. The kid that bought it asked my wife where the down shift "button" was 8O somethings they dont teach you in class. Atleast its a manageable bike to learn on.
	0

04-12-2011, 07:27 PM	#11
FastDoc Join Date: Mar 2009 Location: Southeastern Washington desert Posts: 14,761	Good news! Sometimees we make a little $ on resale. That's the advantage to buying chep and selling cheap. Maybe you need a Pitster Pro 400? 8) __________________ Happy to serve.
	0

04-12-2011, 07:53 PM	#12
katoranger Join Date: May 2007 Location: Altamont, Kansas Posts: 15,103	You're tall enough for a KLR650. They have no problem 2up. http://atlanta.craigslist.org/nat/mcy/2257507135.html __________________ You meet the nicest people on a Honda Clone.
	0

04-12-2011, 08:12 PM	#13
FastDoc Join Date: Mar 2009 Location: Southeastern Washington desert Posts: 14,761	Roger (250 lbs) and I (175 lbs) and about 40 lbs of gear rode his KLR to Odessa (100 miles) last week no trouble. 8) I'm not saying we didn't look silly though. :wink: __________________ Happy to serve.
	0

04-12-2011, 08:56 PM	#14
yellowxj Join Date: Apr 2008 Posts: 79	http://gainesville.craigslist.org/mcy/2319176628.html this ones close to me...carbs cleaned? any way to make sure thats all it needs? I'll email and see if they still have it.
	0

04-12-2011, 09:07 PM	#15
yellowxj Join Date: Apr 2008 Posts: 79	or this one isnt too far away just to flip it. http://jacksonville.craigslist.org/mcy/2313754490.html
	0