Zongshen RX3 Parts Cross Reference: Please Contribute!

[keithmaine]

Spud

All these brake pads, rotors, foot pegs, foot pedals, windshields, etc.
So many forums these things are scattered about, it would be nice to have them in one place in one list.

Could you start a sticky of parts cross ref. that all could contribute to.

[keithmaine]

Oil filter is there just the CSC filters or is there another source??

[SpudRider]

Originally Posted by keithmaine

Oil filter is there just the CSC filters or is there another source??

Until someone discovers otherwise, I don't know of another oil filter which fits the ZS177MM/NC250 engine of the Zongshen RX3.

However, I purchase stainless steel, reusable oil filters for my RX3 from Taobao. They do an excellent job protecting the engine, and are much less expensive than replacing paper oil filters.

https://item.taobao.com/item.htm?spm...cket=10#detail



However, I wouldn't be surprised if a BMW or KTM motorcycle employs these oil filters.

[Co2]

ZS177MM / NC250 Clutch crossreference = Honda dominator 650 , NX 650 EBC CK1170 series dimensions bit tight tolarance 0.01-2mm , same, i used that on my ZS177MM / NC250 confirmed


Note : originals better , only use if cant find original clutchs, just instead exigency (on travel need repair or...)

[SpudRider]

Originally Posted by Co2

ZS177MM / NC250 Clutch crossreference = Honda dominator 650 , NX 650 EBC CK1170 series dimensions bit tight tolarance 0.01-2mm , same, i used that on my ZS177MM / NC250 confirmed


Note : originals better , only use if cant find original clutchs, just instead exigency (on travel need repair or...)

Thank you, Sir!

I always suspected the RX3 clutch parts were Honda parts. Here is a list of the Honda motorcycles which employ the same friction plates, fiber plates, and clutch springs as the Zongshen RX3.

Honda XR650L
Honda XR600R
Honda NX650
Honda CR500R
Honda CR480R
Honda CR250R

A lot of people like the Tusk Clutch Kits you can purchase from Rocky Mountain ATV/MC.

https://www.rockymountainatvmc.com/p...ch-Kit?v=11638

[Co2]

Originally Posted by SpudRider

Thank you,

I always suspected the RX3 clutch parts were Honda parts. Here is a list of the Honda motorcycles which employ the same friction plates, fiber plates, and clutch springs as the Zongshen RX3.

Honda XR650L
Honda XR600R
Honda NX650
Honda CR500R
Honda CR480R
Honda CR250R

A lot of people like the Tusk Clutch Kits you can purchase from Rocky Mountain ATV/MC.

https://www.rockymountainatvmc.com/p...ch-Kit?v=11638

You're welcome , but i warn, on link and photo " metal disk's " i no idea im just use nx650 dominator clutch plates , friction metal discs i use old originals, and seeing photos metal discs i think much bold.

Here my old acc, on forum mt, search and dimensions maybe have idea, again

http://www.motosiklet.net/forum/mt-a...-tip-uyum.html

EBC CK 1170 clutch's is very tight tolarance but ok worked.

[SpudRider]

Originally Posted by Co2

You're welcome , but i warn, on link and photo " metal disk's " i no idea im just use nx650 dominator clutch plates , friction metal discs i use old originals, and seeing photos metal discs i think much bold.

Here my old acc, on forum mt, search and dimensions maybe have idea, again

http://www.motosiklet.net/forum/mt-a...-tip-uyum.html

EBC CK 1170 clutch's is very tight tolarance but ok worked.

Are the Honda, clutch fiber plates the same thickness as the RX3, clutch fiber plates? If you have the opportunity, please also measure the thickness of the RX3, clutch metal plates.

When I have time, I will also check the dimensions of the clutch plates in my Honda CRF250X.

[Co2]

Originally Posted by SpudRider

Are the Honda, clutch fiber plates the same thickness as the RX3, clutch fiber plates? If you have the opportunity, please also measure the thickness of the RX3, clutch metal plates.

When I have time, I will also check the dimensions of the clutch plates in my Honda CRF250X.

Terminology mixed , my Tarzan style

Organic/Fiber plate is ok , butif u add link on photos metal friction metal plates impossible, not need measured, many time i assemb/dissasemb clutch , if photo correct any a optical game " F " optic playing idk, but im think on photos that metal discs impossible mounted rx3 or zs177 or nc250

Measured sorry, motor block is complete , but if wait me 2-3 day later maybe, i promise.

116 mm ( in chamber , non tooth.) , 9 mm(in circle to out walls non toth) , 136 mm (out chamber) Dimensions of the metal plate.

Edit for measurement for Spud, bestregards.

Sorry bad Photos by sj1000 (because my suck xperia u phone probably today REGL/menstruation
, %+&%+/% waste phone never buy.)

Nx 650 dominator Fiber/organic idk, clutchs on my zs177mm, i used it 500 kilometer than, non problem, just mounted very tight tolaration, thick but worked i cant feel any problem it worked.

Edit 2 sj1000 need setup for date and watch. , photos is fresh 10 min ago.

[SpudRider]

Originally Posted by keithmaine

Spud

All these brake pads, rotors, foot pegs, foot pedals, windshields, etc.
So many forums these things are scattered about, it would be nice to have them in one place in one list.

Could you start a sticky of parts cross ref. that all could contribute to.

I think this thread is an excellent start for that project, Keith. I am pinning this thread to the top of this forum. As members contribute equivalent parts to this thread, I will compile an organized list of parts. I will place that organized list in a closed thread, which I will also pin to the top of this forum.

[keithmaine]

Originally Posted by SpudRider

I think this thread is an excellent start for that project, Keith. I am pinning this thread to the top of this forum. As members contribute equivalent parts to this thread, I will compile an organized list of parts. I will place that organized list in a closed thread, which I will also pin to the top of this forum.

Spud

your simply awesome

[SpudRider]

Originally Posted by keithmaine

Spud

your simply awesome

Thank you for coming up with the great idea, Keith.

[keithmaine]

Thank you for listening, I find this forum to be one of the best forums I have ever been part of.

[SpudRider]

Originally Posted by keithmaine

Thank you for listening, I find this forum to be one of the best forums I have ever been part of.

It is members such as you who make these forums such a great place to frequent.

[Weldangrind]

Originally Posted by keithmaine

Thank you for listening, I find this forum to be one of the best forums I have ever been part of.

Originally Posted by SpudRider

It is members such as you who make these forums such a great place to frequent.

This is such a cool shop to hang out in.

[SpudRider]

I have posted a thread with confirmed parts which fit the Zongshen RX3. This closed thread is pinned to the top of this forum, at the following link.

http://www.chinariders.net/showthread.php?t=15532

Please post your confirmed parts in this thread, and I will add those parts to the closed list. If I forget to add any items to the closed list, please don't hesitate to inform me in this thread. Thank you.