|
05-07-2013, 09:21 PM | #1 |
Join Date: Dec 2009
Location: Alaska
Posts: 914
|
LOTS of LIFAN GY-5 parts AND motor parts
Everything you see here as well as a front wheel and a COMPLETE PARTS MOTOR (167FML pushrod version) I can pick parts off of as needed. I may have other parts that are not visible in the photo, PM for condition of parts or better photos I'm letting them go cheap to those in need. :wink:
__________________
Dune buggy build http://chinariders.net/modules.php?n...wtopic&t=14470 400cc lifan build vid: http://youtu.be/20HoU8OK_Y0 other fun: http://tinyurl.com/wildalaskan |
|
05-08-2013, 01:26 AM | #2 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Shipping from AK or MT? I'd be interested in the pushrod motor, but shipping might be prohibitively expensive for me.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
05-08-2013, 01:27 AM | #3 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Do you have a good set of plastic side covers? Got a close-up pic of them?
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
05-08-2013, 01:55 AM | #4 |
Join Date: Dec 2009
Location: Alaska
Posts: 914
|
The upper white one has a little crack below the rear screw hole and was damaged by a forklift when it was being unloaded from the barge Shipping is from alaska so the entire motor would probably not be possible, I think the valves and bore have been damaged from getting stored out side anyways
__________________
Dune buggy build http://chinariders.net/modules.php?n...wtopic&t=14470 400cc lifan build vid: http://youtu.be/20HoU8OK_Y0 other fun: http://tinyurl.com/wildalaskan |
|
05-08-2013, 02:03 AM | #5 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
I think that those would require more fab work than the GY150 covers I already bought. Is the tank plastic? Got a pic?
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
05-08-2013, 02:18 AM | #6 |
Join Date: Dec 2009
Location: Alaska
Posts: 914
|
I am planing on using the gas tank for the buggy project actually
__________________
Dune buggy build http://chinariders.net/modules.php?n...wtopic&t=14470 400cc lifan build vid: http://youtu.be/20HoU8OK_Y0 other fun: http://tinyurl.com/wildalaskan |
|
05-08-2013, 10:06 AM | #7 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Ok, thanks anyway. I can't think of anything else I can use.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
05-09-2013, 06:05 PM | #8 |
Join Date: Mar 2012
Location: Altoona, Fl
Posts: 158
|
How much would you let the motor go for?
__________________
NewStar DB 200 Facts are meaningless. You could use facts to prove anything that's even remotely true! --Homer Simpson |
|
05-09-2013, 10:16 PM | #9 |
Join Date: Dec 2009
Location: Alaska
Posts: 914
|
The motor has a bad top end from sitting out side and shipping from alaska would be $100+
__________________
Dune buggy build http://chinariders.net/modules.php?n...wtopic&t=14470 400cc lifan build vid: http://youtu.be/20HoU8OK_Y0 other fun: http://tinyurl.com/wildalaskan |
|
05-26-2013, 07:47 AM | #10 |
Join Date: Sep 2006
Location: The Quiet Corner of CT.
Posts: 387
|
I'd be interested in the front headlight housing if its still around... I have a Roketa db 05 and the housing is cracked in two. I see it in your o.p. but barely. Any chance on a front and back photo..?
__________________
2006 HIBIRD QH200-st atv, 2005 Kinroad 200GY-01, 2006 Roketa DB-05, 1980 Kawasaki KZ440 LTD |
|
05-26-2013, 09:05 AM | #11 |
Join Date: May 2013
Location: finger lakes NY
Posts: 2,061
|
Is the harness i spy complete? If so how much shipped to 60473? Thanks!
|
|
05-26-2013, 11:24 AM | #12 |
Join Date: Mar 2012
Location: Altoona, Fl
Posts: 158
|
I think that is a polisport mmx headlight
__________________
NewStar DB 200 Facts are meaningless. You could use facts to prove anything that's even remotely true! --Homer Simpson |
|
05-26-2013, 01:19 PM | #13 | ||
Join Date: Dec 2009
Location: Alaska
Posts: 914
|
Quote:
Quote:
my first wiring harness failed and it took over a year of searching to find one that would work because they changed the wiring harness between years and countrys that the bikes were shipped to ( still had to change the turn signal wires on the bike to match this one). if you would like I can take pictures of all the connectors and you can compare it to yours.
__________________
Dune buggy build http://chinariders.net/modules.php?n...wtopic&t=14470 400cc lifan build vid: http://youtu.be/20HoU8OK_Y0 other fun: http://tinyurl.com/wildalaskan |
||
|
05-26-2013, 01:22 PM | #14 | |
Join Date: May 2013
Location: finger lakes NY
Posts: 2,061
|
Quote:
ifplugs dont match up thats not thebiggest issue forme to dealwith...LOLilike bullet connectors...easier to crimp than the stupid molex plug style....although i have acess to those too....LOL |
|
|
06-08-2013, 01:49 PM | #15 |
Join Date: Jun 2013
Location: Hudson Valley NY
Posts: 98
|
Hello Wild_Alaskan I was wondering if you had the throttle grip assembly for sale? I also need the choke cable, headlight plastic, and front brake booster if you have it available. Thanks man!
Last edited by nyvdub89; 06-08-2013 at 02:15 PM. Reason: gramatic error |
|
|
|
|
|