Hawk 250 parts identification - Page 3

hertz9753 · 08-30-2016, 07:21 AM

Quote:

Originally Posted by Republic

Where do these go?

Those cable guides for the front forks.

http://www.rickypowersports.com/#!hawk-250cc/z4ztr

Republic · 08-30-2016, 08:34 PM

Where does the middle sized spring go? I know largest is for kickstand and smallest is brake return/switch, but I can't figure out where to put the middle one.

hertz9753 · 08-30-2016, 09:04 PM

Looks like I should check the wiring under the rear fender.

hertz9753 · 08-30-2016, 11:15 PM

https://www.youtube.com/results?sear...o+250+assembly

I skipped the rubber inserts on the front fender and just used washers because I couldn't get the screws to line up.

Republic · 08-30-2016, 11:38 PM

Hertz, I owe you a beverage of your choice. I finally got it all put together. Hopefully tomorrow I'll get to hear it run.

I have 2 rubber pieces left, I think they go on the rear to cover the 4 bolts holding on that part you sent a photo of earlier. I'll post a photo tomorrow if I can't figure it out.

Thanks again!

hertz9753 · 08-31-2016, 01:57 AM

Good luck!

"Somebody" asked why I was laying on the floor when I was taking that picture. Something about rolling in poo like my dog. The only answer I could come up with was but I don't do it on the lawn.

TCalYen · 12-26-2016, 05:29 PM

Quote:

Originally Posted by Sport Rider

Let me scan my install manual in and send it to you. the larger washer was for the brake pedal for the rear brake. cotter pin too. I don't recall having another washer.

Hi everyone -

New to the forum and SO glad it exists and is active.

I just got the Hawk for my 13 year old son and oh boy. No assembly instructions.

I know there is a scanned one floating around. Could someone please email it to me. Would be greatly appreciated.

Jon - tcalyen@yahoo.com

OUTERLIMITS · 12-26-2016, 10:32 PM

Quote:

Originally Posted by TCalYen

Hi everyone -

New to the forum and SO glad it exists and is active.

I just got the Hawk for my 13 year old son and oh boy. No assembly instructions.

I know there is a scanned one floating around. Could someone please email it to me. Would be greatly appreciated.

Jon - tcalyen@yahoo.com

I don't have a Hawk, but this is off the RPS website.....

http://therps.net/DB-Hawk.html

**JerryHawk250** · 12-27-2016, 09:06 AM

Quote:

Originally Posted by hertz9753

Do the new Hawks now come without the rear fender installed?

I had to install mine on a 2016 black Hawk

Customx253 · 01-23-2017, 04:36 PM

Quote:

Originally Posted by TCalYen

Hi everyone -

New to the forum and SO glad it exists and is active.

I just got the Hawk for my 13 year old son and oh boy. No assembly instructions.

I know there is a scanned one floating around. Could someone please email it to me. Would be greatly appreciated.

Jon - tcalyen@yahoo.com

I could use a copy of the directions as well. peter.smooth@gmail.com

joeboyk · 01-23-2017, 05:26 PM

you can also go to you tube and there is an assembly video,it helped me out with a few questions i had.hope that helps

JMM · 03-02-2017, 02:46 PM

Hey guys. Sorry to highjack. I have a stupid question. I'm putting my Hawk together and was was wondering, does the front axle bolt need the spacer that. And with the long bolt and nut? And if so, what side, Caliper side, on the outside of the forks?

timcosby · 03-02-2017, 06:49 PM

caliper side inside of the forks
yes it needs it

08-30-2016, 11:15 PM	#34
hertz9753 Join Date: May 2016 Location: Bismarck, ND Posts: 868	https://www.youtube.com/results?sear...o+250+assembly I skipped the rubber inserts on the front fender and just used washers because I couldn't get the screws to line up. __________________ 2015 and 3/4 RPS Hawk 250. Most people would call it a 2016 but the MCO didn't.
	0

08-31-2016, 01:57 AM	#36
hertz9753 Join Date: May 2016 Location: Bismarck, ND Posts: 868	Good luck! "Somebody" asked why I was laying on the floor when I was taking that picture. Something about rolling in poo like my dog. The only answer I could come up with was but I don't do it on the lawn. __________________ 2015 and 3/4 RPS Hawk 250. Most people would call it a 2016 but the MCO didn't.
	1

01-23-2017, 05:26 PM	#41
joeboyk Join Date: Dec 2016 Location: Akron OH area Posts: 103	Assembly you can also go to you tube and there is an assembly video,it helped me out with a few questions i had.hope that helps
	0

03-02-2017, 06:49 PM	#43
timcosby Join Date: Nov 2016 Location: robertsdale alabama usa Posts: 1,007	caliper side inside of the forks yes it needs it __________________ 1991 harley heritage softail classic 2016 hawk kaw h1 400 tripple 13' long chopper in progress 2009 johnny pag bar hog 2004 hd electra glide ultra classic shriner edition 1997 harley davidson 1200 sportster 1972 harley davidson amf sx250
	0

08-30-2016, 08:34 PM	#32
Republic Join Date: Jul 2015 Posts: 118	Where does the middle sized spring go? I know largest is for kickstand and smallest is brake return/switch, but I can't figure out where to put the middle one.
	0

08-30-2016, 11:38 PM	#35
Republic Join Date: Jul 2015 Posts: 118	Hertz, I owe you a beverage of your choice. I finally got it all put together. Hopefully tomorrow I'll get to hear it run. I have 2 rubber pieces left, I think they go on the rear to cover the 4 bolts holding on that part you sent a photo of earlier. I'll post a photo tomorrow if I can't figure it out. Thanks again!
	0

03-02-2017, 02:46 PM	#42
JMM Join Date: Feb 2017 Posts: 58	Hey guys. Sorry to highjack. I have a stupid question. I'm putting my Hawk together and was was wondering, does the front axle bolt need the spacer that. And with the long bolt and nut? And if so, what side, Caliper side, on the outside of the forks?
	0