Go Back   ChinaRiders Forums > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search
Page 1 of 2 1 2
Showing results 1 to 25 of 42
Search took 0.01 seconds. Search: Posts Made By: SpudRider
Forum: Zongshen RX3 05-30-2016, 02:00 AM
Replies: 104
Views: 38,689
Posted By SpudRider
Thanks for reporting this information, Doug. :) ...

Thanks for reporting this information, Doug. :)

I had a problem with my stock rear hub, and CSC sent me a replacement. However, I suspect CSC sent me a hub from one of their test bikes, which...
Forum: Zongshen RX3 05-30-2016, 01:51 AM
Replies: 104
Views: 38,689
Posted By SpudRider
Thanks for posting this information, Jay. The...

Thanks for posting this information, Jay. The diagram for the rear wheel shows two bearings, which matches my wheel. However, I overlooked item #20, since it lacked a diagram. ;)

Apparently the...
Forum: Zongshen RX3 05-29-2016, 01:56 PM
Replies: 104
Views: 38,689
Posted By SpudRider
I agree. The bearings are inexpensive, and it...

I agree. The bearings are inexpensive, and it certainly doesn't hurt to have extra bearings. ;)

There is a very real possibility that Zongshen changed the design of the rear hub. ;) I am busy...
Forum: Zongshen RX3 05-28-2016, 02:12 AM
Replies: 104
Views: 38,689
Posted By SpudRider
I have had my NC250 engine apart, and it employs...

I have had my NC250 engine apart, and it employs excellent bearings. In addition, all of the photographs I have seen of the engine display excellent bearings. The front wheel bearings of the RX3 are...
Forum: Zongshen RX3 05-28-2016, 01:37 AM
Replies: 104
Views: 38,689
Posted By SpudRider
Post Edited to Correct My Error I was in...

Post Edited to Correct My Error

I was in error, and Ohio_Danimal is correct. I received a replacement hub from CSC, and apparently it was an earlier version of the hub. Members in foreign...
Forum: Zongshen RX3 05-22-2016, 02:47 PM
Replies: 104
Views: 38,689
Posted By SpudRider
In addition to what Peter said, you would also...

In addition to what Peter said, you would also need to carry a slide hammer to use the blind bearing removers. Therefore, the blind bearing removers are actually less compact than the split collet...
Forum: Zongshen RX3 05-19-2016, 02:41 PM
Replies: 104
Views: 38,689
Posted By SpudRider
Thanks for posting the links. SKF makes good...

Thanks for posting the links. SKF makes good bearings. :)
Forum: Zongshen RX3 05-19-2016, 01:59 PM
Replies: 104
Views: 38,689
Posted By SpudRider
You're welcome. :) Can you post a link to...

You're welcome. :)

Can you post a link to the SKC bearings for sale on eBay? ;)
Forum: Zongshen RX3 05-19-2016, 12:03 AM
Replies: 104
Views: 38,689
Posted By SpudRider
I'm sorry; I made a mistake in my previous post. ...

I'm sorry; I made a mistake in my previous post. You need a 15 mm split collet, which is Motion Pro part #08-0264. This split collet will work for the front wheel bearings as well. :)
Forum: Zongshen RX3 05-17-2016, 08:53 PM
Replies: 104
Views: 38,689
Posted By SpudRider
The Zongshen RX3 uses the same bearings as my...

The Zongshen RX3 uses the same bearings as my Zongshen Sierra 200, so I had them in stock. ;)
Forum: Zongshen RX3 05-17-2016, 08:51 PM
Replies: 104
Views: 38,689
Posted By SpudRider
No, the bike didn't ride differently, and my fuel...

No, the bike didn't ride differently, and my fuel mileage was good. :shrug: However, in retrospect, it was harder to turn the rear wheel when lubricating the drive chain. ;)

As long as you have...
Forum: Zongshen RX3 04-29-2016, 07:39 PM
Replies: 104
Views: 38,689
Posted By SpudRider
Using an anchor bolt is ingenious. :) However,...

Using an anchor bolt is ingenious. :) However, nothing is faster than using the following tools. :tup:

I prefer to drive out wheel bearings using a Motion Pro bearing driver and split collet. The...
Forum: Zongshen RX3 04-14-2016, 08:43 PM
Replies: 104
Views: 38,689
Posted By SpudRider
You can easily damage the bearings while driving...

You can easily damage the bearings while driving them out. Therefore, it's usually best to install new bearings after removing the old ones. I always pack new bearings with extra grease before I...
Forum: Zongshen RX3 04-14-2016, 04:24 PM
Replies: 104
Views: 38,689
Posted By SpudRider
Welcome, and thanks for posting the link. :)

Welcome, and thanks for posting the link. :)
Forum: Zongshen RX3 04-14-2016, 04:23 PM
Replies: 104
Views: 38,689
Posted By SpudRider
No, I have never used a power washer on any of my...

No, I have never used a power washer on any of my motorcycles. I always use my garden hose. ;)

Thanks for posting the caveat. :)
Forum: Zongshen RX3 04-13-2016, 01:07 PM
Replies: 104
Views: 38,689
Posted By SpudRider
Indeed, he does make a very fine and useful tool....

Indeed, he does make a very fine and useful tool. :tup:
Forum: Zongshen RX3 04-12-2016, 12:54 PM
Replies: 104
Views: 38,689
Posted By SpudRider
Thanks for the kind words, and the reminder. ;) ...

Thanks for the kind words, and the reminder. ;) I have added this thread to the RX3 Tech Sticky, under the Maintenance subheading. :)

http://www.chinariders.net/showthread.php?t=14228
Forum: Zongshen RX3 04-12-2016, 12:22 PM
Replies: 104
Views: 38,689
Posted By SpudRider
Thanks for posting the link. :)

Thanks for posting the link. :)
Forum: Zongshen RX3 04-12-2016, 11:58 AM
Replies: 104
Views: 38,689
Posted By SpudRider
Can you post a link to the vendor where you...

Can you post a link to the vendor where you purchased your bearings? I'm sure others will appreciate knowing this information. :) Fortunately, I purchased a good supply of these bearings several...
Forum: Zongshen RX3 04-12-2016, 11:46 AM
Replies: 104
Views: 38,689
Posted By SpudRider
Needless to say, I agree. ;) My peace of mind...

Needless to say, I agree. ;) My peace of mind is much improved now that I have replaced/serviced all of the wheel bearings. :)
Forum: Zongshen RX3 04-12-2016, 11:11 AM
Replies: 104
Views: 38,689
Posted By SpudRider
Here is a photograph of the worn original...

Here is a photograph of the worn original bearings I removed from the rear hub. The 6302 bearing on the left was missing one of the rubber seals. This bearing was locked and dry.

The 6202...
Forum: Zongshen RX3 04-12-2016, 11:07 AM
Replies: 104
Views: 38,689
Posted By SpudRider
Post Edited to Correct Errors Here is a...

Post Edited to Correct Errors

Here is a photograph of the SKF 6202 2RS bearing I installed in the sprocket side of the rear hub. Since I have an earlier version of the rear hub, I only installed...
Forum: Zongshen RX3 04-12-2016, 10:45 AM
Replies: 104
Views: 38,689
Posted By SpudRider
Give it a try; you might be able to do it....

Give it a try; you might be able to do it. :shrug: You have nothing to lose by trying. ;)
Forum: Zongshen RX3 04-12-2016, 10:36 AM
Replies: 104
Views: 38,689
Posted By SpudRider
I made a typographical error in post #39, and I...

I made a typographical error in post #39, and I have corrected it. Thanks for letting me know. :)

Except for the 6004 bearing, all the other bearing numbers end in 02, which indicates an inside...
Forum: Zongshen RX3 04-12-2016, 02:35 AM
Replies: 104
Views: 38,689
Posted By SpudRider
Post Edited to Correct Errors I think the...

Post Edited to Correct Errors

I think the Silk Road Rider only had problems with his rear wheel, and I wouldn't be surprised if it was only the 6202 bearing causing the problem. ;)

The 6302...
Showing results 1 to 25 of 42
Page 1 of 2 1 2

 
Forum Jump

All times are GMT -4. The time now is 12:43 AM.

Contact Us - ChinaRiders.net - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.