Go Back   ChinaRiders Forums > Technical/Performance > ATVs
Register FAQ Community Calendar Today's Posts Search
Reply
 
Thread Tools Search this Thread Display Modes
Old 02-07-2019, 11:14 AM   #1
Dcantk84   Dcantk84 is offline
 
Join Date: Feb 2019
Posts: 6
Question Dc powered cdi question!! Help would be appreciated

Working on a Eton cxl 150
No spark condition
I Have 12.4 to dc cdi and the 12v switched is wired to the brake light switch circuit as oem route. I have 11.6 v because of voltage drop through the bulb (load)
Trigger pickup resistance - 141k ohms and .7 ac v
Exciter coil resistance - 331k ohms and 72 ac v

Do these dc cdis need exactly 12v or higher on switched circuit to fire?
Or am I missing something here?


 
Reply With Quote
Old 02-07-2019, 03:19 PM   #2
humanbeing   humanbeing is offline
 
humanbeing's Avatar
 
Join Date: Mar 2008
Posts: 2,436
That vehicle = An orphan from Taiwan. Thx to the similarities btw GY6 copies, we can find some parts in reasonable price.
Typical chinese dc-CDI works btw 8-16V & outputs around 200V
Don't u measured coil's primary / secondary ohm reading? Spark plug still in OK condition? ... https://get2itparts.com/etontech/PD_CXL150.php
AC reading (although seems OK this time) is useless. Build a Peak Voltage Adapter https://forum.jorsindo.com/forum.php...authorid=86716
GY6 should be something similar to: (don't need to measure Exciter coil when using DC-cdi)
__________________



Last edited by humanbeing; 02-07-2019 at 03:54 PM.
 
Reply With Quote
Old 02-07-2019, 06:43 PM   #3
Dcantk84   Dcantk84 is offline
 
Join Date: Feb 2019
Posts: 6
Yes I am aware that this atv is an orphan haha. So both of my ignition coils primary resistance measures in spec and secondary measures in spec. I have multiple new spark plugs cr7hsa gapped per service manual spec. I dont have the exciter coil hooked up to anything but I can hot wire to an ac cdi and the bike will run but I was trying to maintain the stock setup with a dc cdi. If i test the coil positive wire coming from the cdi I should be getting somewhere around 200 ac volts?


 
Reply With Quote
Old 02-07-2019, 07:30 PM   #4
Dcantk84   Dcantk84 is offline
 
Join Date: Feb 2019
Posts: 6
I have 0.7 ac volts on trigger wire going into cdi
I have 0.52 ac volts going out to ignition coil.....
I have 2 identical vmc chinese dc cdis both are giving me the same output


 
Reply With Quote
Old 02-07-2019, 07:32 PM   #5
Dcantk84   Dcantk84 is offline
 
Join Date: Feb 2019
Posts: 6
obviously the cdi is the source of problem as I can verify I have 12 v constant , 12v switched and 2 grounds, followed by trigger at 0.7ac v but i have the coil positive at 0.52 ac v


 
Reply With Quote
Old 02-07-2019, 07:39 PM   #6
Dcantk84   Dcantk84 is offline
 
Join Date: Feb 2019
Posts: 6
removed 12 volt switched wire AT THE CDI left it connected everywhere else and cdi gives normal ac v output and bike runs

woohoo hope this helps someone in the future.


 
Reply With Quote
Old 02-07-2019, 08:28 PM   #7
humanbeing   humanbeing is offline
 
humanbeing's Avatar
 
Join Date: Mar 2008
Posts: 2,436
Buy 07HGJ-0020100 or equivalent | Homebrew: https://thumpertalk.com/forums/topic...ltage-adapter/
& measures it in dc.
The Taiwan url above shows big 4's shop manual picture, ALL measured in dc via peak voltage adapter
__________________


 
Reply With Quote
Old 02-07-2019, 09:07 PM   #8
Dcantk84   Dcantk84 is offline
 
Join Date: Feb 2019
Posts: 6
power probe 4 my friend... very good investment


 
Reply With Quote
Old 02-07-2019, 10:18 PM   #9
humanbeing   humanbeing is offline
 
humanbeing's Avatar
 
Join Date: Mar 2008
Posts: 2,436
https://otomodif97.wordpress.com/201...-kekuranganya/ had schematic of typical Hondaish 6-pin CDi
__________________


 
Reply With Quote
Old 02-07-2019, 10:33 PM   #10
wheelbender6   wheelbender6 is offline
 
wheelbender6's Avatar
 
Join Date: May 2015
Location: Houston area
Posts: 1,902
AC lies. DC dies. No. Wait a minute...
__________________
"Its not WHAT you ride; its THAT you ride"


 
Reply With Quote
Reply

Tags
cdi, dcv, no spark, stator



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:21 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.