![]() |
#1 |
Join Date: Jul 2019
Location: Lancaster,Ky
Posts: 449
|
Ball joint zerk fittings
Has anybody added grease fittings to their ball joints and if yes,which grease fitting did you use?I have bought some Alemite 3009 drive in zerk fittings which have a 3/32's shank length along with a 3/16" hole and am going to try and do one just to see if it is possible.
|
![]() |
![]() |
#2 |
Join Date: Jul 2019
Location: Lancaster,Ky
Posts: 449
|
Noticed I have a hole in my frame tube in the front on the bottom that is letting water get in.Either weld it or silicone it.Might do both.
|
![]() |
![]() |
#3 |
Join Date: Jul 2019
Location: Lancaster,Ky
Posts: 449
|
I reckon I got it sealed up,hard spot to weld.First couldn't get it to ground so I ground a little paint off,then I couldn't get my big pumpkin head in there with my helmet on so I just closed my eyes and visually welded it in my mind,lol.
|
![]() |
![]() |
#4 |
Join Date: Jul 2019
Location: Lancaster,Ky
Posts: 449
|
Got lucky and still had some black flex seal that hadn't dried up and put some of that on there to cover up the weld.
|
![]() |
![]() |
#5 |
Join Date: Jul 2019
Location: Lancaster,Ky
Posts: 449
|
I see another hole.Wish I had seen that before I put my welder back up.
|
![]() |
![]() |
#6 |
Join Date: Jul 2019
Location: Lancaster,Ky
Posts: 449
|
Got my ball joints and my tie-rod ball joints set up with a grease fitting so I could grease them.You would not believe how much easier it steers now,unbelievable.I didn't get the two on the tie rod near the steering shaft,I'll have to take them off to drill and tap them.I started out using the drive in grease fittings but the 3rd one was loose,where I wiggled the drill while drilling it out,so I went with the 6mm which only required the hole to be one size bigger than 3/16th, a 13/64.
|
![]() |
![]() |
#7 |
Moderator
Join Date: Oct 2016
Location: Houma, La.
Posts: 11,651
|
Nice job. I need to do that on my daughters UTV.
__________________
2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S (Sold) 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel |
![]() |
![]() |
#8 |
Join Date: Jul 2019
Location: Lancaster,Ky
Posts: 449
|
[QUOTE=JerryHawk250;360790]Nice job. I need to do that on my daughters UTV.[
I have been noticing how harder it was to steer.I still like the 2 on the tie rods near the steering shaft,I'll have to take both tie rods loose on both ends to do those. It is easier to steer now. |
![]() |
![]() |
#9 |
Join Date: Jul 2019
Location: Lancaster,Ky
Posts: 449
|
Still got to get my swing arm set up with some grease fittings,next I reckon.Still ain't figured out exactly what I'm going to do to it.
|
![]() |
![]() |
#10 |
Moderator
Join Date: Oct 2016
Location: Houma, La.
Posts: 11,651
|
That was the first ones i installed on my ATV, Hawk And UTV. That seems to get the most wear form water and sand. I pump them up every time we head out to the spillway to help keep water out of the swingarm. So far The 7 year old ATV and 5 year old Hawk and UTV have had no issues with the swing arms.
__________________
2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S (Sold) 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel |
![]() |
|
![]() |
![]() |
|
|