![]() |
#1 |
Join Date: Jan 2015
Location: England
Posts: 382
|
Working With Diagnostic Data Cable & Software
UPDATE (June 2020)
The PCHUD software is now completely obsolete & has been superseded by the fully functional HUD ECU Hacker software. Thanks goes to Raptorix (Elmüsoft) for creating & developing this new software. Detailed description & download for the HUD ECU Hacker can be found here https://netcult.ch/elmue/HUD%20ECU%20Hacker/ ************************************************** ******* LINK UPDATE (2018) See post 164 & 165 for PCHUD download This is an all in one download that includes PCHUD with instructions "Clear fault codes" software with instructions A guide to making your own data connection using a vag com cable and other info Requirements ---------------- 1/ Data Cable Taobao link http://item.taobao.com/item.htm?id=39520023502 so far the only one known to work 2/ PC or laptop running Win7 (32bit), Tested May work with other O.S. NOT 64bit ---------------------------------------------- The diagnostic software comes indirectly with the cable. If this is not the case, below is a link to the software I received (PCHUD) https://mega.co.nz/#!skACACIT!Kv8o9g...KYCK-q08TiBUs8 The software is in Chinese, below is a link, in the download are files and instructions translated in to English. I will go in to more detail of these files further on in this post https://mega.co.nz/#!wwgkDAwR!QzhC2n...cYKva96H8_KMuY Installing USB drivers and running software ------------------------------------------------- The translated instructions included in my link should do the trick, so i will only write an overview here. The setup.exe for the USB drivers can be found in the "USB数据线驱动程序及安装指南" folder Run the setup without the cable connected to your laptop No installation is required for the PCHUD software The folder "德尔福电脑检测软件(PCHud_Chinese)" needs to be renamed to PCHUD, then just place the folder in the root of the harddrive . I used D:\ as described in the instructions, but probably would work else where if you edit the pchud.ini Check the pchud.ini anyway to make sure the directory entries are correct. --------------- Launch and experiment with the software without anything connected (run hud.exe) The important data to load is the .par file, this holds all the parameter data. The VARI54CN.PAR file is the one that you can see being used in the Delphi Scan Tool Manual (included in my download). Unfortunately the VARI54CN.PAR is in chinese but i have done my best at translating it (3.par) The .hud files are user configuration files for the gauges. You are able to create new ones from within the program. so to get you started use - 3.hud with 3.par or 1.hud with 1.par ( slightly different translation of VARI54CN.PAR) Translating or editing of .par files yourself i will cover in a later post, but i have included a hex/text editor that will be required in my download) ---------------------------------------------------------- The Chinese TR125 (QJ125GY-16A) uses the Delphi MT05 , i have included the EFI section of the manual in my download. The images show them using the MT05common.PAR as their parameter file. For this use 2.hud with 2.par (slight variation on the MT05common.PAR) ---------------------------------------------------------- connecting up --------------- with ignition off plug the cable into the bike, USB to laptop and run PCHUD. make sure comports are configured, bike kill switch is to "run" turn on ignition. "com time out error " should go after a short while, if not start engine and all should be good apologies for the length of, post now completed ![]() Last edited by katflap; 06-11-2020 at 09:11 AM. Reason: new download info |
![]() |
![]() |
#2 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Thanks for posting this excellent thread, Kat.
![]() My fifth order with Taobao is ready for shipment, but I am delaying it, because I am adding this cable to my order. ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
![]() |
![]() |
#3 |
Join Date: Jan 2015
Location: England
Posts: 382
|
Thanks Spud,
I'm still adding more stuff to my first post over the next few hours, fitting it in around other things i have to do, will mark it as completed when done ![]() I also added the cable to an existing order, the agent received the cable very quickly, so in the end it was waiting on components to arrive for my existing order that held up the shipment. I had 2 orders shipped at nearly the same time, this one got through, the other got caught in customs. so i will have to pay duty on that one ![]() |
![]() |
![]() |
#4 |
Join Date: Jan 2015
Location: England
Posts: 382
|
Translating,Editing .par files
Open the .par file with M.S. Word , select other encoding Chinese simplified(EUC).
From here you can translate by copying in to google translate. For editing ( software provided in 1st post download) Open .par file , in the right hand column you will see sections of code strings. select view, character set, International, Chinese simplified so you can match the chinese characters . Note the start point , change back to ACSll and edit TIP - 00 in the left hex column = nothing. ** this all takes forever to do** If your editing one of my .par files , they are already in English. ![]() |
![]() |
![]() |
#5 |
Join Date: Jan 2015
Location: England
Posts: 382
|
Simulating A Fault
I disconnected the O2 sensor to see what would happen.
as you can see in the pic it displayed that the fault light was on and recorded at fault number of 49. This means from the table a P0031 fault, Oxygen sensor Heater high voltage. ![]() Not quite what I was expecting but at least it was the right component ![]() ![]() |
![]() |
![]() |
#6 |
Join Date: May 2007
Location: Warshington
Posts: 928
|
As a total nube what does this do for me and the bike? Is it for going in and changing parameters to make it a BMW or KTM?
![]() |
![]() |
![]() |
#7 | |
Join Date: Jan 2015
Location: England
Posts: 382
|
Quote:
![]() The ability for changing parameters which will effect the way your bike runs is yet unknown. The parameters I have mentioned in my posts are only related to the diagnostic software (PCHUD) on your PC so that it understands the data it is being feed from the bike. Also its well cheap ![]() |
|
![]() |
![]() |
#8 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
You are certainly going to get more data from a computer than you will from an OBD2 scanner.
![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
![]() |
![]() |
#9 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
What???
Don't apologize for an awesome contribution like that! You're the man. ![]()
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
![]() |
#10 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
He's not the Grand Poobah for nothing.
![]() ![]()
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." ![]() 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
![]() |
![]() |
#11 | |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Quote:
The gauge in my truck is somewhat vague, and it's in Metric. I still think in Fahrenheit when it comes to cars, and I like to know what my engine is doing when I'm towing my holiday trailer. The connector and software for an RX3 will allow you to pinpoint trouble down the road, because it will tell you if you have a faulty throttle position sensor, oxygen sensor or whatever else. A very wise tool investment.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
![]() |
![]() |
#12 |
Join Date: Mar 2008
Posts: 2,436
|
VW cable (twenty-odd yuan) mod :http://www.chyangwa.net/forum.php?mo...uthorid=652893
__________________
Last edited by humanbeing; 04-21-2016 at 09:39 PM. |
![]() |
![]() |
#13 |
Join Date: Jan 2012
Location: ChCh , NZ
Posts: 2,265
|
On the XT660 the fault code is displayed on the dash automaticly once a fault is detected.
you instantly know what bit just stuffed up yer day.... Dose the RX3 do the same? you can change some of the injection setting from the dash in dialoge mode... TPS / CO etc .
__________________
09 XT660R ... 06 TTR250 ... 80 Montesa H6 125 Enduro... 77 Montesa Cota 348 MRR "Malcom Rathnell Replica"... Current resto projects.. 81 Honda CT110... 80 Kawasaki KL250A1... 11 Husaburg TE125 enduro... "sold" along with another 31... Lifan 125 Pitbike.. "stolen" ... KIWI BIKER FORUM...... http://www.kiwibiker.co.nz/forums/content.php All the best offroad rides in NZ... http://www.remotemoto.com/ E-mail... xtpete1@gmail.com |
![]() |
![]() |
#14 | |
Join Date: May 2015
Location: Cambridge, England
Posts: 140
|
Quote:
Maybe an option buried somewhere deep in the OBC?
__________________
- - - - - - - - - - - - - - - - - - - - - - - Riding bikes for over 40 years Honda C50 / SS50 / CB125 / CB250 Velocettes (various) Piaggio's / Honda's / Yamaha's Raptor . . . . the List Goes On . . . . |
|
![]() |
![]() |
#15 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Nope. Old '99 GMC truck with analogue gauges. Not the fancy modern type.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
![]() |
|
![]() |
![]() |
|
|