Brozz 250 idling too high -

vonnsue · 09-29-2019, 10:31 PM

Hi y'all!

New to the forum and just put together my bike- a Brozz 250 Blue Angel.

I've started it up no problem but she keeps revving past 7-8000 rpms in idle. I tried setting the idle back on the carb but it doesn't seem to make a difference.
I've started it several times with no change.
I also checked the throttle and it's not stuck in any way.

I'm newbie when it comes to engines/bikes and not sure what to do and I'm open to any suggestions you might have.

Thanks for your help!

V

duck9191 · 09-30-2019, 02:22 AM

Sounds like it's sucking air from somewhere it shouldn't be. Make sure the nuts that hold the carb on are tight as well as the ones that hold the carb mounting flange to the head. Unscrew the slide cap where the throttle cable goes in, there should be a gasket in the top of cap but they can fall out.

herbie · 09-30-2019, 05:44 AM

Quote:

Originally Posted by vonnsue

I've started it up no problem but she keeps revving past 7-8000 rpms in idle

7000-8000 rpm's is wide open throttle, make sure the throttle is returning to the seated ( throttle off position) at the handlebars. If you had the carb off the bike the throttle slide may be put back in the wrong position.

If the 7000-8000 rpms was a mistake on your part and it's idling high but not that high then check your choke position. The lever on the left side of the carb is the choke lever, all the way down is off, middle position is half choke, all the way up is full choke. Unless your in a very cold climate, set the check on the middle position and start the bike let it idle for a few seconds and turn the choke off.(push the lever down)

vonnsue · 10-01-2019, 01:33 AM

Thanks so much for the feedback guys! I had pulled the throttle cable too much when I assembled it and there was a gap on the top of the carb. Problem solved!

wedooit · 10-01-2019, 12:25 PM

Quote:

Originally Posted by vonnsue

Thanks so much for the feedback guys! I had pulled the throttle cable too much when I assembled it and there was a gap on the top of the carb. Problem solved!

Hey von! Welcome here, post a pix or two!

PeaceSportsAtlanta · 10-04-2019, 04:34 PM

Quote:

Originally Posted by vonnsue

Thanks so much for the feedback guys! I had pulled the throttle cable too much when I assembled it and there was a gap on the top of the carb. Problem solved!

Are you fellow out by Las Vegas who called me? Very tough to diagnose bikes by phones. Glad the forum was able to help get it solved!!!

Red Hawk · 10-06-2019, 08:39 PM

My mixture screw fell off my carb when I was out on a ride. I know I know HOW!? The bike was stuck a 4K every time i was at 0% throttle. Fun day. Was hard to spot too.

vonnsue · 10-14-2019, 07:26 PM

Hey Y'all,

Any advice on breaking in a brand new Brozz 250?

timcosby · 10-14-2019, 09:53 PM

just wondering if anyone has an older one and can answer this question. do these blue plastics hold up better to the sun than the black hawk ones. mine are turning greyish with swirls!

duck9191 · 10-14-2019, 10:21 PM

Quote:

Originally Posted by vonnsue

Hey Y'all,

Any advice on breaking in a brand new Brozz 250?

Ride it. Don't baby it, don't beat the hell out of it, no sustained full throttle and vary the rpms. Change the oil often for the first few times, they don't have a filter so all the crap stays suspended in the oil.

09-29-2019, 10:31 PM	#1
vonnsue Join Date: Sep 2019 Posts: 4	Brozz 250 idling too high - Hi y'all! New to the forum and just put together my bike- a Brozz 250 Blue Angel. I've started it up no problem but she keeps revving past 7-8000 rpms in idle. I tried setting the idle back on the carb but it doesn't seem to make a difference. I've started it several times with no change. I also checked the throttle and it's not stuck in any way. I'm newbie when it comes to engines/bikes and not sure what to do and I'm open to any suggestions you might have. Thanks for your help! V
	0

09-30-2019, 02:22 AM	#2
duck9191 Join Date: May 2019 Location: Port Huron, Michigan Posts: 637	Sounds like it's sucking air from somewhere it shouldn't be. Make sure the nuts that hold the carb on are tight as well as the ones that hold the carb mounting flange to the head. Unscrew the slide cap where the throttle cable goes in, there should be a gasket in the top of cap but they can fall out. __________________ 2020 Triumph Tiger 900 rally. 2018 Bashan Storm 250. pz30b, digital cluster + gear indicator, unifilter and car customs full exhaust. 2019 Taotao 110b boulder atv. The "arm breaker" lol 2007 Honda VTX 1300R. 1974 Suzuki tm125, work in progress 2001 Suzuki Drz 400s.
	3

10-06-2019, 08:39 PM	#7
Red Hawk Join Date: Jul 2018 Location: NEPA Posts: 273	My mixture screw fell off my carb when I was out on a ride. I know I know HOW!? The bike was stuck a 4K every time i was at 0% throttle. Fun day. Was hard to spot too. __________________ 2018 Hawk P&P Decked .040 off the head. 17/43 D.I.D. 428, NGK Iridium plug, DeCat, Wrapped pipe, Custom S.S. Muffler core, Nibbi PE30 115/35, L.E.D. Lights, Digital Cluster, USB port, Cutting Bord skid plate, Oil cooler w/ custom CRF oil filter inline, 5Wt fork oil, Rear Shock, CNC Back Rack, 30mm FAT bars, Bark Busters, ProGrips, Adjustable levers, Shinko 700’s lots of Loctite!
	0

10-14-2019, 09:53 PM	#9
timcosby Join Date: Nov 2016 Location: robertsdale alabama usa Posts: 1,007	just wondering if anyone has an older one and can answer this question. do these blue plastics hold up better to the sun than the black hawk ones. mine are turning greyish with swirls! __________________ 1991 harley heritage softail classic 2016 hawk kaw h1 400 tripple 13' long chopper in progress 2009 johnny pag bar hog 2004 hd electra glide ultra classic shriner edition 1997 harley davidson 1200 sportster 1972 harley davidson amf sx250
	0

10-01-2019, 01:33 AM	#4
vonnsue Join Date: Sep 2019 Posts: 4	Thanks so much for the feedback guys! I had pulled the throttle cable too much when I assembled it and there was a gap on the top of the carb. Problem solved!
	4