Trailmaster TM35

TraverseBay · 05-15-2023, 10:22 AM

Hello... New here.

I have a 2023 Trailmaster TM 35 coming in a week or so which has a YS - CB250F 5SPD motor and I am just wondering if anyone here has one and if anyone has done modifications to it.

I am curious if the stock carburetor is decent, or should I go ahead and order one now. And if so, would a 28 mm be adequate or should I opt for a 30 mm. According to the website, it comes with a PE 28 carb from the factory. I have experience using Mikuni carbs only, but it seems here that a Nibbi carbs are a favorite. Any opinions on that are welcome.

Secondly, does anyone have a recommendation for an exhaust for this or is the exhaust already decent to begin with?

Thanks for any interest shown in my questions, and I'm open to whatever suggestions you guys may have.

Thanks,

Jason

**JerryHawk250** · 05-15-2023, 11:00 AM

Welcome aboard! Ride it as is and give it time to break in before doing any mods. Being that it comes with a the Nibbi it might already be tuned.

Fast_Freddy · 05-15-2023, 02:18 PM

Quote:

Originally Posted by TraverseBay

Hello... New here.

I have a 2023 Trailmaster TM 35 coming in a week or so which has a YS - CB250F 5SPD motor and I am just wondering if anyone here has one and if anyone has done modifications to it.

I am curious if the stock carburetor is decent, or should I go ahead and order one now. And if so, would a 28 mm be adequate or should I opt for a 30 mm. According to the website, it comes with a PE 28 carb from the factory. I have experience using Mikuni carbs only, but it seems here that a Nibbi carbs are a favorite. Any opinions on that are welcome.

Secondly, does anyone have a recommendation for an exhaust for this or is the exhaust already decent to begin with?

Thanks for any interest shown in my questions, and I'm open to whatever suggestions you guys may have.

Thanks,

Jason

Welcome Jason. I'm pretty sure that the TM35 is very similar to the Templar 250. The Carb is fine except that you need to remove a plug that hides the idle mixture screw and either slot the bolt heads or grind them off to remove the float bowl to rejet. I chose to grind the heads off and buy replacement SS allen bolts from my local hardware store.

As for the exhaust, I am not aware of a direct replacement performance pipe. The best option seems to be to decat the oem pipe. GL

TraverseBay · 05-30-2023, 05:11 PM

Thanks. I got the bike and rode it for the first time today after going through the install process. I put a Nibbi 28mm carb with a 42 pilot and 112 main. So far so good with the pilot, I breaking it in so time will tell if the main is good.

The spark plug looks nice and tan and throttle response is good, so I'm thinking the pilot jet of 42 is a good size.

The motor is the same as the Templar Pro , a ZS172FMM -3A
Once I break in a little bit more I'll be able to test and see if 112 is a good mean or not. Anyone running this carb set up on this motor, what are you running for your main jet?

I do have a question about setting valve clearances on this motor. I have experiences with the smaller YX piranha motors, but this is completely different. A write-up or video on how exactly to get in there and do the valves on this motor would be super helpful. It seems like there's not a lot of space to work in.

Thanks for any assistance anyone can provide.

Jason

Fast_Freddy · 05-31-2023, 12:35 AM

If you ride in Denver, CO that 112 main jet may not be too lean. Stock is 120, many of us are running 125 and I know a few running 130-140. I'm at ~300 ASL, most are between 100-2000' ASL. Thumper did a nice valve DIY guide you can find here. I recommend removing the seat and gas tank for easier access.

TraverseBay · 05-31-2023, 10:17 AM

Great. Thanks for that info and link, that is exactly what I as looking for.

I am about it 600' ASL in Northern Michigan so I looks like I may have to increase jetting soon.

05-15-2023, 10:22 AM	#1
TraverseBay Join Date: May 2023 Location: Michigan Posts: 4	Trailmaster TM35 Hello... New here. I have a 2023 Trailmaster TM 35 coming in a week or so which has a YS - CB250F 5SPD motor and I am just wondering if anyone here has one and if anyone has done modifications to it. I am curious if the stock carburetor is decent, or should I go ahead and order one now. And if so, would a 28 mm be adequate or should I opt for a 30 mm. According to the website, it comes with a PE 28 carb from the factory. I have experience using Mikuni carbs only, but it seems here that a Nibbi carbs are a favorite. Any opinions on that are welcome. Secondly, does anyone have a recommendation for an exhaust for this or is the exhaust already decent to begin with? Thanks for any interest shown in my questions, and I'm open to whatever suggestions you guys may have. Thanks, Jason
	2

05-15-2023, 11:00 AM	#2
JerryHawk250 Moderator Join Date: Oct 2016 Location: Houma, La. Posts: 11,734	Welcome aboard! Ride it as is and give it time to break in before doing any mods. Being that it comes with a the Nibbi it might already be tuned. __________________ 2024 Linhai 300 ATV 4x4 2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S (Sold) 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel
	0

05-31-2023, 12:35 AM	#5
Fast_Freddy Join Date: Nov 2022 Location: Pennsyltuckey Posts: 311	If you ride in Denver, CO that 112 main jet may not be too lean. Stock is 120, many of us are running 125 and I know a few running 130-140. I'm at ~300 ASL, most are between 100-2000' ASL. Thumper did a nice valve DIY guide you can find here. I recommend removing the seat and gas tank for easier access. __________________ 22 Templar 250
	0

05-30-2023, 05:11 PM	#4
TraverseBay Join Date: May 2023 Location: Michigan Posts: 4	Thanks. I got the bike and rode it for the first time today after going through the install process. I put a Nibbi 28mm carb with a 42 pilot and 112 main. So far so good with the pilot, I breaking it in so time will tell if the main is good. The spark plug looks nice and tan and throttle response is good, so I'm thinking the pilot jet of 42 is a good size. The motor is the same as the Templar Pro , a ZS172FMM -3A Once I break in a little bit more I'll be able to test and see if 112 is a good mean or not. Anyone running this carb set up on this motor, what are you running for your main jet? I do have a question about setting valve clearances on this motor. I have experiences with the smaller YX piranha motors, but this is completely different. A write-up or video on how exactly to get in there and do the valves on this motor would be super helpful. It seems like there's not a lot of space to work in. Thanks for any assistance anyone can provide. Jason
	0

05-31-2023, 10:17 AM	#6
TraverseBay Join Date: May 2023 Location: Michigan Posts: 4	Great. Thanks for that info and link, that is exactly what I as looking for. I am about it 600' ASL in Northern Michigan so I looks like I may have to increase jetting soon.
	1