10-09-2014, 12:57 AM | #31 | |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Quote:
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
|
10-09-2014, 02:56 AM | #32 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
As always, thanks for your feedback, Weld.
The Delphi, MT05 diagnostic plug only employs three wires, as shown in the Delphi service manual. The OBD2 code specifies the following wiring, as shown at the link below. Pins 4&5: Ground Pins 7&8: K-Line Pin 16: +12V Battery http://www.bmwgm5.com/Peake_AB03.htm I might as well convert the RX3, 6-pin Delphi connectors to 3-pin Delphi connectors, which I can get from eBay. http://www.ebay.com/itm/New-Delphi-W...p2054897.l4275 I am inclined to purchase the following adapter, and wire the correct OBD2 pins to the corresponding Delphi pins, using one of the 3-pin Delphi connectors. http://www.ebay.com/itm/Diagnostic-C..._Tools&vxp=mtr I can then connect this OBD2 adapter harness to any OBD2 scanner, such as the inexpensive, OBD2 scanner shown in the link below. http://www.ebay.com/itm/Autel-MS300-...p2054897.l4275
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 Last edited by SpudRider; 10-09-2014 at 05:37 AM. |
|
10-09-2014, 10:23 AM | #33 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
That is certainly an economical way to go. After you've adapted the harness and purchased the connector, perhaps you could borrow a higher quality scanner from Andy to see what other features might be useful.
You might also choose to buy an OBDII connector that will plug into a laptop, which could allow for custom fuel mapping, etc.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
10-09-2014, 01:17 PM | #34 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
|
10-09-2014, 05:06 PM | #35 |
Join Date: Sep 2014
Location: Blue Ridge Mtns Ga
Posts: 437
|
Dobeck
Looks very promising. Copy of their reply.
Thank you for your interest in a Dobeck Performance fuel solution. It is very possible for us to develop a fuel solution. We would either need one of these bikes available to test with or some specific tech information to see if we have a solution available. I have informed R&D about your interest. I will contact you with an update as soon as I hear back from them. Will you have one of these bikes? Where are you located? Let me know if you have any other questions. Regards, Dillon Binstock | Dobeck Performance Sales | Marketing
__________________
Mark 2015 Haosen Hawk 250 2014 CRF250L 2014 CB500X Rally Raid |
|
10-09-2014, 10:28 PM | #36 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Thanks for posting the update, Mark. How long do they need the bike for testing?
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
10-10-2014, 01:00 AM | #37 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
So cool! I'd happily give up my bike for awhile to allow for tuning development.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
10-10-2014, 07:49 AM | #38 |
Join Date: Sep 2014
Location: Blue Ridge Mtns Ga
Posts: 437
|
I'll follow up with them and find out how long they need it.
__________________
Mark 2015 Haosen Hawk 250 2014 CRF250L 2014 CB500X Rally Raid |
|
10-10-2014, 11:36 AM | #39 |
Join Date: Sep 2014
Location: Blue Ridge Mtns Ga
Posts: 437
|
The folks at Dolbek are very responsive and seem interested in our Chinese thumper.
Here is there latest reply. "Mark, In a perfect world, we could finalize an application in about a week. However, we usually have multiple projects going on at once. Two weeks is probably a more accurate statement and that is if we don’t have any technical hurdles. Will you have this bike available once it is released into the USA? Where are you located at? Talk to you soon."
__________________
Mark 2015 Haosen Hawk 250 2014 CRF250L 2014 CB500X Rally Raid |
|
10-10-2014, 12:52 PM | #40 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Two weeks is a long time. Does the lender get a free EJK Fuel Controller?
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
10-11-2014, 07:27 AM | #41 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
As I speculated in post #14 of this thread, the following OBD2 to USB cable should connect the Delphi MT05 ECM to a computer.
http://www.ebay.com/itm/VAGCOM-USB-K..._Tools&vxp=mtr
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
10-11-2014, 07:38 AM | #42 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
The following photograph shows all the components of the Delphi EFI system employed by the Zongshen RX3.
Here are links to various components of the EFI system which are sold at Tabao. Delphi MT05 ECM http://item.taobao.com/item.htm?spm=...82&ns=1#detail Delphi Fuel Pump http://item.taobao.com/item.htm?spm=...22&ns=1#detail Delphi Fuel Injector http://item.taobao.com/item.htm?spm=...70&ns=1#detail Delphi Oxygen Sensor http://item.taobao.com/item.htm?spm=...40&ns=1#detail Delphi Fuel Filter http://item.taobao.com/item.htm?spm=...45&ns=1#detail
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
10-13-2014, 07:11 PM | #43 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
That would be a good point of negotiation. Even half price would be nice.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
10-14-2014, 10:35 AM | #44 |
Join Date: Sep 2008
Location: central PA
Posts: 770
|
obd2
so is there a an adapter cable available to go from the delphi plug on the rx3,,,to my obd2 scan tool?? if so i want one.
__________________
2015 zongshen rx3,,(Sold),,,2016 bashan storm,,2005 Harley ultra classic. |
|
10-14-2014, 10:39 AM | #45 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
I don't know of any adapter cable which will connect the Delphi plug to an OBD2 scan tool. Therefore, I am going to make one, using the parts I mentioned in post #33 of this thread.
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
|
|
|
|