![]() |
#16 |
Join Date: Nov 2019
Location: Woodbridge VA
Posts: 60
|
Bob
very easy to install. message me if you can so I can send you pics of the installation and the links to the units I used. Carl |
![]() |
![]() |
#17 |
Join Date: Dec 2018
Location: PNW
Posts: 983
|
If you have time, can you post the link to the unit you used?
|
![]() |
![]() |
#18 |
Join Date: Nov 2019
Location: Woodbridge VA
Posts: 60
|
I used this oil cooler. do NOT cut the springs, they are for protecting the hoses.
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 you can use this one for the oil cooler plate for the head of the motor. DO NOT destroy the original gasket. Needs to be used for the new oil plate. https://www.ebay.com/itm/Pit-Bike-OI...ZqGae&LH_BIN=1 Carl Last edited by daytonacat; 09-16-2020 at 09:47 AM. |
![]() |
![]() |
#19 |
Join Date: Nov 2019
Location: Woodbridge VA
Posts: 60
|
almost forgot;
the bolt closest to the spark plug on the plate ALSO holds the circular plate on the other side of the head inplace. There is a LOCATING tab on that plate to keep it in place when you tighten down that one long bolt. Torque all 3 bolts to 7 to 8 Ft Lbs. use a drop of blue lock tight on each one. ALSO see this link to see my oil cooler instllation on my STOCK Vader. https://www.chinariders.net/showthread.php?t=25925 |
![]() |
![]() |
#20 |
Join Date: Aug 2020
Location: Colorado
Posts: 84
|
Got the headlights retrofitted guys. Hope you like them! I swear I'm going to do a night ride video tonight to show you how they look. Get you the 20$ dremal set at Walmart so you can cut into the housing and everything else is just screws and the housing itself pops open easy since there is no silicone. I think it turned out great!
Dremal I used (just buy you some good cutting wheels for 5$): https://www.walmart.com/ip/Hyper-Tou...RoCm48QAvD_BwE |
![]() |
![]() |
#21 |
Join Date: Aug 2020
Location: Colorado
Posts: 84
|
|
![]() |
![]() |
#22 | |
Join Date: Dec 2018
Location: PNW
Posts: 983
|
Quote:
|
|
![]() |
![]() |
#23 |
Join Date: Nov 2019
Location: Woodbridge VA
Posts: 60
|
Bob
how is the heat build up on the actual LED light you installed in the Vaders headlight assembly? Carl |
![]() |
![]() |
#24 |
Join Date: Nov 2019
Location: Woodbridge VA
Posts: 60
|
You are very welcome China
|
![]() |
![]() |
#25 | |
Join Date: Aug 2020
Location: Colorado
Posts: 84
|
Quote:
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 I think our fork diameter is like 44mm or 1.7 inches so these should do since they are up to 2". This is going to look sick with a light bar right under the headlight housing if all goes well. I have this light in mind: https://www.amazon.com/dp/B07MYYCLHG...v_ov_lig_dp_it |
|
![]() |
![]() |
#26 |
Join Date: Nov 2019
Location: Woodbridge VA
Posts: 60
|
Bob
when you take the headlight apart, can you please take a few pics to show us how you actually mounted up that light inside of it? thanks dont forget you can angle the headlight assembly by loosening up the SINGLE screw under the high beam on the headlight schroud. |
![]() |
![]() |
#27 | |
Join Date: Aug 2020
Location: Colorado
Posts: 84
|
Quote:
|
|
![]() |
![]() |
#28 |
Join Date: Nov 2019
Location: Woodbridge VA
Posts: 60
|
Bob
did you use the original throttle cable on your after market carb or a different one? Carl |
![]() |
![]() |
#29 | |
Join Date: Aug 2020
Location: Colorado
Posts: 84
|
Quote:
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 Also here is the pictures of the install. I angled the light down a bit, put some self tapping screws to make sure it didn't move and boom, better light now! I am putting a light bar on today attached to the forks to just give it that amazing light I need on dirt roads and stuff. Here is the install pictures: |
|
![]() |
|
![]() |
![]() |
Tags |
colorado, grom clone, medicbobs, vader 125 |
|
|