Vitacci Terminator 300cc 4x4 atv - Page 5

dugndeep · 06-15-2024, 10:00 AM

Now I'm looking to purchase a service manual for the Linhai 260/300 4x4 atv.I have a couple already downloaded & saved on my computer but I want a paper back version.I just don't know if my printer could print out 360 pages plus whether I got the ink to do that.

dugndeep · 07-09-2024, 10:37 AM

I've been going around the atv trying to find all the zerk grease fittings and applying some grease to them.I think I have found them all & am now wondering about the front hub carrier bearings.Their like the old cars & tractors ect & their not a sealed bearing.

dugndeep · 07-09-2024, 10:47 AM

The 2wdhub carrier looks like it has a place for a zerk fitting.To where the 4wd does not,I was just wondering if I could drill & tap for a zerk fitting?

**JerryHawk250** · 07-09-2024, 10:49 AM

I would drill and tap it to install a grease zerk.

dugndeep · 07-09-2024, 10:54 AM

That's the 2wd version above & I don't know if that is a threaded hole for the zerk fitting or not.The 4wd doesn't have that & has the splined shaft running through it.

dugndeep · 07-09-2024, 10:58 AM

I suppose you might could on the back side of the rotor.

dugndeep · 07-09-2024, 11:17 AM

I think they skimped on the grease in the fittings,some I don't think they put any grease in & that's why I'm worried about the front axle bearings.

dugndeep · 07-09-2024, 11:23 AM

I'll have to take the wheel off,cotter pin & nut just to see what kind of grease is in there.There's a grease fitting on the steering shaft,I had to take the front cover off to get to it & they must have never put any grease in it,so much easier to steer after putting grease in the steering bushing.

**JerryHawk250** · 07-09-2024, 11:26 AM

As long as the zerk doesn't interfere with the bearings or shaft, I wouldn't think you would have any issues with installing one.

dugndeep · 07-09-2024, 11:42 AM

Parts catalog.I'm trying,one picture is to big & the other is so small you can't hardly see it.I'll just have to take the hub carrier off to see.

06-15-2024, 10:00 AM	#61
dugndeep Join Date: Jul 2019 Location: Lancaster,Ky Posts: 449	Now I'm looking to purchase a service manual for the Linhai 260/300 4x4 atv.I have a couple already downloaded & saved on my computer but I want a paper back version.I just don't know if my printer could print out 360 pages plus whether I got the ink to do that. Last edited by dugndeep; 06-18-2024 at 10:05 AM.
	0

07-09-2024, 10:49 AM	#64
JerryHawk250 Moderator Join Date: Oct 2016 Location: Houma, La. Posts: 11,618	I would drill and tap it to install a grease zerk. __________________ 2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S (Sold) 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel
	0

07-09-2024, 11:26 AM	#69
JerryHawk250 Moderator Join Date: Oct 2016 Location: Houma, La. Posts: 11,618	As long as the zerk doesn't interfere with the bearings or shaft, I wouldn't think you would have any issues with installing one. __________________ 2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S (Sold) 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel
	1

07-09-2024, 11:42 AM	#70
dugndeep Join Date: Jul 2019 Location: Lancaster,Ky Posts: 449	Parts catalog.I'm trying,one picture is to big & the other is so small you can't hardly see it.I'll just have to take the hub carrier off to see. Attached Thumbnails
	0

07-09-2024, 10:37 AM	#62
dugndeep Join Date: Jul 2019 Location: Lancaster,Ky Posts: 449	I've been going around the atv trying to find all the zerk grease fittings and applying some grease to them.I think I have found them all & am now wondering about the front hub carrier bearings.Their like the old cars & tractors ect & their not a sealed bearing.
	0

07-09-2024, 10:47 AM	#63
dugndeep Join Date: Jul 2019 Location: Lancaster,Ky Posts: 449	The 2wdhub carrier looks like it has a place for a zerk fitting.To where the 4wd does not,I was just wondering if I could drill & tap for a zerk fitting?
	1

07-09-2024, 10:54 AM	#65
dugndeep Join Date: Jul 2019 Location: Lancaster,Ky Posts: 449	That's the 2wd version above & I don't know if that is a threaded hole for the zerk fitting or not.The 4wd doesn't have that & has the splined shaft running through it.
	0

07-09-2024, 10:58 AM	#66
dugndeep Join Date: Jul 2019 Location: Lancaster,Ky Posts: 449	I suppose you might could on the back side of the rotor.
	0

07-09-2024, 11:17 AM	#67
dugndeep Join Date: Jul 2019 Location: Lancaster,Ky Posts: 449	I think they skimped on the grease in the fittings,some I don't think they put any grease in & that's why I'm worried about the front axle bearings.
	0

07-09-2024, 11:23 AM	#68
dugndeep Join Date: Jul 2019 Location: Lancaster,Ky Posts: 449	I'll have to take the wheel off,cotter pin & nut just to see what kind of grease is in there.There's a grease fitting on the steering shaft,I had to take the front cover off to get to it & they must have never put any grease in it,so much easier to steer after putting grease in the steering bushing.
	0