2022 RX3 Mystery rattle 6000rpm-8000RPM Help!!!

Ten85 · 07-27-2023, 05:13 PM

Good afternoon everyone. First time posting and using a forum. Bear with me. I bought a 2022 CSC RX3. I have produced a rattle vibration and i cannot put my finger on, it might have always been there cause i did not notice it until after 500 miles when i starting brining the RPMS up. I have absolutely checked everything i can think of. Around 6k-8k i get loud rattle where i am bout to wear ear plugs. I checked all engine mounts, engine guards, skid plate every bolt i can see. I pulled the exhaust just to make sure they installed an exhaust gasket. It was there but i still replaced it anyways. Could not find my stethoscope so used a screw driver. Engine feels smooth, the most noise/vibration i can find it right on the exhaust, but still not sure. i pulled off the skid plate and heat shield and the noise was still there. I took it to a local motorcycle shop to make sure it was not engine noise. They said the engine sounded fine, but i cannot find this rattle it is driving me nuts.

Rattle is there in Neutral, its there with clutch lever pulled in, its there moving or not. Has anyone had a similar issue.

Thank you for your time.

bigdano711 · 07-27-2023, 07:15 PM

My guess is to check the valve lash...might be loose?

Ten85 · 07-27-2023, 07:55 PM

Valves are good. That what i thought maybe. First adjusted them to .08 mm went back and put them at .06 mm and all is good there.

Ten85 · 08-02-2023, 01:17 PM

Found out what it was. Engine was bad and blew up 400 miles after this post. Sounds like a crank or rod. CSC is sending me a new engine. Fantastic customer service. lets hope this engine is not bad..

bigdano711 · 08-02-2023, 10:42 PM

I was gonna suggest plastics, 'cause mine rattled pretty loud at certain RPM's until I found that forward bolt and cinched it down.

outboardr · 11-06-2023, 09:31 PM

Quote:

Originally Posted by Ten85

Found out what it was. Engine was bad and blew up 400 miles after this post. Sounds like a crank or rod. CSC is sending me a new engine. Fantastic customer service. lets hope this engine is not bad..

Are you back on the road with the new engine?

07-27-2023, 05:13 PM	#1
Ten85 Join Date: Jan 2023 Location: Port Angeles, WA Posts: 3	2022 RX3 Mystery rattle 6000rpm-8000RPM Help!!! Good afternoon everyone. First time posting and using a forum. Bear with me. I bought a 2022 CSC RX3. I have produced a rattle vibration and i cannot put my finger on, it might have always been there cause i did not notice it until after 500 miles when i starting brining the RPMS up. I have absolutely checked everything i can think of. Around 6k-8k i get loud rattle where i am bout to wear ear plugs. I checked all engine mounts, engine guards, skid plate every bolt i can see. I pulled the exhaust just to make sure they installed an exhaust gasket. It was there but i still replaced it anyways. Could not find my stethoscope so used a screw driver. Engine feels smooth, the most noise/vibration i can find it right on the exhaust, but still not sure. i pulled off the skid plate and heat shield and the noise was still there. I took it to a local motorcycle shop to make sure it was not engine noise. They said the engine sounded fine, but i cannot find this rattle it is driving me nuts. Rattle is there in Neutral, its there with clutch lever pulled in, its there moving or not. Has anyone had a similar issue. Thank you for your time. Last edited by Ten85; 07-27-2023 at 05:54 PM.
	0

07-27-2023, 07:15 PM	#2
bigdano711 Join Date: Jun 2023 Location: Big Piney, WY Posts: 619	My guess is to check the valve lash...might be loose? __________________ 2023 Hawk 250 from XPRO off of Amazon MOUNTAIN MAN RC + MOTO on YouTube "If there were more bloody noses, there would be less wars." - Hagbard Celine John 2:15 So He made a whip out of cords and drove all from the temple area, both sheep and cattle; He scattered the coins of the money changers and overturned their tables.
	0

08-02-2023, 01:17 PM	#4
Ten85 Join Date: Jan 2023 Location: Port Angeles, WA Posts: 3	Found out what it was. Engine was bad and blew up 400 miles after this post. Sounds like a crank or rod. CSC is sending me a new engine. Fantastic customer service. lets hope this engine is not bad.. Last edited by Ten85; 08-02-2023 at 02:43 PM.
	2

08-02-2023, 10:42 PM	#5
bigdano711 Join Date: Jun 2023 Location: Big Piney, WY Posts: 619	I was gonna suggest plastics, 'cause mine rattled pretty loud at certain RPM's until I found that forward bolt and cinched it down. __________________ 2023 Hawk 250 from XPRO off of Amazon MOUNTAIN MAN RC + MOTO on YouTube "If there were more bloody noses, there would be less wars." - Hagbard Celine John 2:15 So He made a whip out of cords and drove all from the temple area, both sheep and cattle; He scattered the coins of the money changers and overturned their tables.
	0

07-27-2023, 07:55 PM	#3
Ten85 Join Date: Jan 2023 Location: Port Angeles, WA Posts: 3	Valves are good. That what i thought maybe. First adjusted them to .08 mm went back and put them at .06 mm and all is good there.
	1