05-25-2022, 02:53 PM
|
#1 |
|
Join Date: May 2022
Location: Kansas
Posts: 11
|
Bike help?
I’ve been calling around local shops to see if they’ll do it to no avail. Is there someone on the forum that does fabrication/welding? I’d so please drop me a line so I can get this project of mine steered in the right direction.
It’d be most appreciated. 
|
|
|
05-25-2022, 08:35 PM
|
#2 |
|
Join Date: Oct 2016
Location: Carrollton, GA
Posts: 1,467
|
What do you need help with in the welding/fab department? I have a small-ish welder, so perhaps I can help out with something.
__________________
First Rule of Aviation: -Never Pass Up The Opportunity to Pee I was struggling to get my wife's attention; I sat down on the couch and looked comfortable. That did the trick! My wife says I only have two faults. I don't listen and something else... If at first you don't succeed, try doing it the way I told you to... The Stable: 2005 Yamaha V-Star 650 - SOLD 2015 Suzuki DR 650 2015 RPS Hawk 250 - SOLD 2016 Ural Gear Up |
|
|
|
05-25-2022, 08:49 PM
|
#3 |
|
Join Date: May 2022
Location: Kansas
Posts: 11
|
I need to have some mounts and stuff for a engine made to fit my project bike. The engines and pans have clearing issues so I was tryna move it up a bit. But I can’t find a shop that will fab up some square tubing for me and if they do it’s $$$ as heck.
|
|
|
|
05-26-2022, 04:45 AM
|
#4 |
|
Join Date: Oct 2016
Location: Carrollton, GA
Posts: 1,467
|
Can you post some pictures and measurements/dimensions? I would say PM me, but I don't think you can put pictures in PMs. I'll take a look and see what I can do to help out.
__________________
First Rule of Aviation: -Never Pass Up The Opportunity to Pee I was struggling to get my wife's attention; I sat down on the couch and looked comfortable. That did the trick! My wife says I only have two faults. I don't listen and something else... If at first you don't succeed, try doing it the way I told you to... The Stable: 2005 Yamaha V-Star 650 - SOLD 2015 Suzuki DR 650 2015 RPS Hawk 250 - SOLD 2016 Ural Gear Up |
|
|
|
05-26-2022, 11:34 AM
|
#5 |
|
Join Date: May 2022
Location: Kansas
Posts: 11
|
I posted some on my intro thread. If you wanna take a look I still havnt done measurements yet because or work stuff haha. It’d the one titled “hey people”
Last edited by Crazyrigged; 05-26-2022 at 11:36 AM. Reason: More typing |
|
|
|
05-27-2022, 06:09 PM
|
#6 |
Join Date: May 2015
Location: Houston area
Posts: 1,902
|
Somebody that fabricates race cars may be willing. Lots of dirt track racers out there.
__________________
"Its not WHAT you ride; its THAT you ride" |
|
|
|
05-28-2022, 09:39 PM
|
#7 | |
|
Join Date: May 2022
Location: Kansas
Posts: 11
|
Quote:
|
|
|
|
|
05-28-2022, 10:33 PM
|
#9 | |
|
Join Date: May 2022
Location: Kansas
Posts: 11
|
Quote:
|
|
|
|
|
|
|
 |
| Tags |
| fabrication, project |
|
|
Linear Mode
