New Member Awaiting Rhino 250 - Page 2

Mudflap · 01-09-2020, 08:01 PM

Pretty much all the fasteners on the Rhino are flange bolts and nylock nuts so no loctite needed. Never had a fastener come loose on mine in 700 hours.

david3921 · 01-11-2020, 11:48 PM

Quote:

Originally Posted by Darth Racer

Ok so not too bad... it's on it's way... cool.

Brush up on some of the threads here that talk about putting it together... the fender flares can be tricky... I have a thread on it http://www.chinariders.net/showthread.php?p=215343. Throw the wrenches out that come with it.. they are useless.

Get a small bottle of BLUE Loctite

Drain the stir fry oil out of the crankcase and replace with 15/40 Rotella oil. Get a couple of quarts. It's good to change out the oil after the first break in run (4hrs of riding or so) Clean off the bits of metal from the magnet on the drain plug

Pick up a couple of NGK spark plugs.. it will start easier

Clean out an area of the garage to do the assembly in

It's winter now... don't leave that battery out in the cold or it wont last long at all.

Just another thing to add to the great advice from Darth, set your valve clearances. Most of these CB's come from the factory with tight valves.

justin1328 · 01-14-2020, 05:47 PM

Thanks to everyone for the warm welcomes and advice. Received my Rhino Friday afternoon 1/10/20. First thing I did before assembly was to sand, prime and paint the entire body. Wasn’t a fan of the blue. Went with a dark charcoal metallic enamel and it turned out great! Changed the oil and used Royal Purple break in oil. New NGK Plug, 2” rear spacers, and aligned the front wheels. One odd thing I noticed was that when I changed the oil, there was shavings on the drain plug and the oil was a little dark. Assuming they test run the engines before mounting??? Getting ready to add a front and rear light bar, Trail Tech Vapor and a couple odds and ends. Anyway, I will post pictures once I figure out a hosting site for the pics. Thanks again to everyone, looking forward to contributing in the near future. Praying for a BIG snow storm in the coming weeks 😊

Darth Racer · 01-15-2020, 09:07 PM

Shavings are normal from what I understand on new small engines.... its why you do the first handful of oil changes after only a little bit of riding.

Yes I would imagine they do a test to make sure it runs before shipping... avoids a lot of BS on returns.

If Mudflap says Loctite not needed then you should be good.. I do vaguely remember some of the bolts were nylocks ... some weren't think the fender screws are what I put it on mostly.

Yes please do post some pics.. Charcoal sounds sharp with black trim... Imgur.com works pretty good for images.

justin1328 · 01-16-2020, 12:39 PM

https://imgur.com/gallery/SkY78kP

Darth Racer · 01-16-2020, 10:10 PM

The link doesn't work Justin.... copy paste the "direct link" to the image.

**JerryHawk250** · 01-24-2020, 12:24 PM

She came out looking real nice.

justin1328 · 01-24-2020, 02:20 PM

Jerry, Thank you, and I am grateful for this community for being such an amazing resource. Gave me the confidence to pull the trigger on the purchase.

01-14-2020, 05:47 PM	#18
justin1328 Join Date: Dec 2019 Location: Somers Point, NJ Posts: 37	Received. Thanks to everyone for the warm welcomes and advice. Received my Rhino Friday afternoon 1/10/20. First thing I did before assembly was to sand, prime and paint the entire body. Wasn’t a fan of the blue. Went with a dark charcoal metallic enamel and it turned out great! Changed the oil and used Royal Purple break in oil. New NGK Plug, 2” rear spacers, and aligned the front wheels. One odd thing I noticed was that when I changed the oil, there was shavings on the drain plug and the oil was a little dark. Assuming they test run the engines before mounting??? Getting ready to add a front and rear light bar, Trail Tech Vapor and a couple odds and ends. Anyway, I will post pictures once I figure out a hosting site for the pics. Thanks again to everyone, looking forward to contributing in the near future. Praying for a BIG snow storm in the coming weeks 😊
	0

01-16-2020, 12:39 PM	#20
justin1328 Join Date: Dec 2019 Location: Somers Point, NJ Posts: 37	https://imgur.com/gallery/SkY78kP Last edited by justin1328; 01-24-2020 at 01:35 PM. Reason: Updated Images
	2

01-24-2020, 12:24 PM	#22
JerryHawk250 Moderator Join Date: Oct 2016 Location: Houma, La. Posts: 11,715	She came out looking real nice. __________________ 2024 Linhai 300 ATV 4x4 2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S (Sold) 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel
	0

01-09-2020, 08:01 PM	#16
Mudflap Join Date: Sep 2014 Posts: 1,929	Pretty much all the fasteners on the Rhino are flange bolts and nylock nuts so no loctite needed. Never had a fastener come loose on mine in 700 hours.
	0

01-15-2020, 09:07 PM	#19
Darth Racer Join Date: Apr 2016 Location: MD Posts: 558	Shavings are normal from what I understand on new small engines.... its why you do the first handful of oil changes after only a little bit of riding. Yes I would imagine they do a test to make sure it runs before shipping... avoids a lot of BS on returns. If Mudflap says Loctite not needed then you should be good.. I do vaguely remember some of the bolts were nylocks ... some weren't think the fender screws are what I put it on mostly. Yes please do post some pics.. Charcoal sounds sharp with black trim... Imgur.com works pretty good for images.
	0

01-16-2020, 10:10 PM	#21
Darth Racer Join Date: Apr 2016 Location: MD Posts: 558	The link doesn't work Justin.... copy paste the "direct link" to the image.
	0

01-24-2020, 02:20 PM	#23
justin1328 Join Date: Dec 2019 Location: Somers Point, NJ Posts: 37	Jerry, Thank you, and I am grateful for this community for being such an amazing resource. Gave me the confidence to pull the trigger on the purchase.
	1