Minki carb not shutting all the way

Hammertime · 04-25-2018, 09:55 PM

Put carb on Vader 125 and can't get it to shit all the way a run wide open started

Hammertime · 04-25-2018, 10:12 PM

Do you need long throttle cable

ben2go · 04-26-2018, 10:56 AM

Are you talking to yourself?

Give the cable all the slack you can and check the routing to make sure the cable isn't kinked. If that is good and the problem persists, you may need a different cable. I'm not familiar enough with the small bikes to advise on which cable.

Weldangrind · 04-26-2018, 11:55 AM

Is it possible that the slide is in backwards?

Lkhangee · 05-06-2018, 11:16 AM

The needle might be bent. Or might be stucking int the emulsion tube which usually happens when the needle jet is improperly seated. (the jet through which the needle goes in /out)

Arcstriker29 · 05-06-2018, 09:34 PM

When I swapped carbs, it took some messing around to get the throttle right, but first like some one else mentioned, check to make sure the slide is in correctly, it might need to be rotated 180 degrees... OR see if there is any play at all when you twist the throttle, or is it tight and only turn a short distance? I try to set mine so there is minimal play, but not so the cable is being tugged when released. A lot of these carbs have different cable settings from 1 to another.

Adjuster · 05-07-2018, 10:58 AM

My guess is the little metal ferrule at the end of the throttle cable is not seated all the way down into the nipple on top of the carb. Essentially causing your cable to be just slightly shorter.

/

04-25-2018, 09:55 PM	#1
Hammertime Join Date: Apr 2018 Posts: 7	Minki carb not shutting all the way Put carb on Vader 125 and can't get it to shit all the way a run wide open started
	0

04-26-2018, 11:55 AM	#4
Weldangrind Join Date: Mar 2009 Location: Sardis, BC, Canada Posts: 25,977	Is it possible that the slide is in backwards? __________________ Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer
	5

04-25-2018, 10:12 PM	#2
Hammertime Join Date: Apr 2018 Posts: 7	Do you need long throttle cable
	0

04-26-2018, 10:56 AM	#3
ben2go Join Date: Jun 2011 Posts: 1,335	Are you talking to yourself? Give the cable all the slack you can and check the routing to make sure the cable isn't kinked. If that is good and the problem persists, you may need a different cable. I'm not familiar enough with the small bikes to advise on which cable.
	0

05-06-2018, 11:16 AM	#5
Lkhangee Join Date: Jul 2016 Posts: 48	The needle might be bent. Or might be stucking int the emulsion tube which usually happens when the needle jet is improperly seated. (the jet through which the needle goes in /out)
	0

05-06-2018, 09:34 PM	#6
Arcstriker29 Join Date: Mar 2018 Location: New Hampshire Posts: 34	When I swapped carbs, it took some messing around to get the throttle right, but first like some one else mentioned, check to make sure the slide is in correctly, it might need to be rotated 180 degrees... OR see if there is any play at all when you twist the throttle, or is it tight and only turn a short distance? I try to set mine so there is minimal play, but not so the cable is being tugged when released. A lot of these carbs have different cable settings from 1 to another.
	0

05-07-2018, 10:58 AM	#7
Adjuster Join Date: Dec 2014 Location: Deerfield Beach FL Posts: 1,410	My guess is the little metal ferrule at the end of the throttle cable is not seated all the way down into the nipple on top of the carb. Essentially causing your cable to be just slightly shorter. /
	1