Confirmed Compatible Parts: Zongshen RX3

SpudRider · 11-18-2015, 02:48 PM

This thread contains a list of parts from other motorcycles which have been confirmed to fit the Zongshen RX3. This is a closed list. Please contribute your discovery of any parts which fit the Zongshen RX3 in the following thread.

http://www.chinariders.net/showthread.php?t=15528

Brake Pads

Front Brake Pads: EBC FA185

If you click the following link, you will download the EBC catalog.

http://ebcbrakes.com/Assets/ecatalog...Cat.html#p=282

On page 282 you will find the FA185 brake pads. This page lists all the different motorcycles which employ these brake pads. Buy sintered, front brake pads for any of these motorcycles, and they will fit the front brake caliper of your Zongshen RX3.

Rear Brake Pads: EBC FA140, EBC FA496

The RX3 motorcycles imported to the United States by CSC have the latest, rear brake caliper. The U.S. bikes use the EBC FA140, EBC FA496 brake pads employed by the following Japanese motorcycles.

Honda CB500X, NC700X
Triumph Tiger 800

Honda CBR250R, CBR300R, CB300F, CBR650F
Suzuki GW250, SFV650

Clutch Parts

Here is a list of the Honda motorcycles which employ the same clutch fiber plates, and clutch springs as the Zongshen RX3.

Honda XR650L
Honda XR600R
Honda NX650
Honda CR500R
Honda CR480R
Honda CR250R

It is reported the Honda, clutch metal plates are too thick.

Shift Lever

The Honda XR650L shift lever is slightly longer than the RX3 shift lever. However, this Honda shift lever, and the many aftermarket shift levers for the Honda XR650L, have a folding tip.

The folding tip prevents damage to the shift lever and the engine, should you drop the motorcycle on its left side.

Rear Sprocket

The JTR473 sprocket is identical to the Zongshen RX3 sprocket for bikes with the rear cushion drive.

http://www.jtsprockets.com/catalogue/sprocket/JTR473-40

This sprocket is available with 40T, and 37T.

SpudRider · 11-18-2015, 03:25 PM

Spark Plug

The stock spark plug is a Denso U22ESR-N. Denso spark plugs are somewhat hard to find in the United States. Here is a list of other, equivalent spark plugs.

NGK CR7E : Gap 0.031 inches (0.08 mm)
Champion RG96C

SpudRider · 11-19-2015, 03:52 AM

Electrical Connectors

Auxiliary Power Plug: Sumitomo, HTW 110 connectors (2-Pin)
Headlight Connector: Furukawa, RFW 090 connectors (6-Pin)
ECU Diagnostic Port: Furukawa, RFW 090 connectors (6-Pin)

SpudRider · 12-09-2015, 11:05 AM

Throttle Position Sensor (TPS)

Delphi SS10459
UPC: 689604104682

5S5008 - AirTex/Wells
SS10459 - Delphi

SpudRider · 12-19-2015, 08:40 PM

Vapor Canister Purge Valve

The solenoid purge valve for the evaporative emissions canister is the Delphi 1997278, ACDelco 214-641 unit.

http://www.ebay.com/itm/Evaporative-...3D130848197922

SpudRider · 12-19-2015, 08:42 PM

MAP/MAT Sensor

The Delphi 28086011, ACDelco 12232201 MAP sensor is equivalent to the MAP/MAT sensor of the Zongshen RX3. Just make sure you get a 4-pin connector (MAT). It's best if the sensor has a sticker which labels the 4 pins: VOut, 5V, MAT, GND.

http://www.ebay.com/sch/sis.html?_nk...p2047675.m4096

SpudRider · 12-19-2015, 10:37 PM

The following, radiator fan switch is equivalent to the switch employed by the Zongshen RX3. This switch is designed for the following Suzuki and Kawasaki motorcycles.

Suzuki

GSX-R600 97-05
GSX-R750 96-08
VL/VZ800 01-11
DL1000 V-Strom 03-09
GSX-R1000 01-04
SV1000 03-07
TL1000R/S 98-03
GSX-R1300 “Hayabusa” 99-07

Kawasaki

Ninja ZX-6R 2003-2004
ZX636 2003-2004
ZX600 2003-2004

http://www.ebay.com/sch/i.html?_from...witch&_sacat=0

SpudRider · 04-13-2016, 08:52 AM

Rear Hub Bearing Sizes

Rear Hub Bearing, Sprocket Side: 6202 2RS
Rear Hub Bearing, Brake Rotor Side: 6302 2RS

Sprocket Carrier Bearing: 6004 2RS

Front Hub Bearing Sizes

(2) 6302 2RS

SpudRider · 03-21-2017, 06:28 AM

I have verified the EBC, MD929D brake rotor is a perfect fit for the front wheel of the Zongshen RX3. This brake rotor fits the following motorcycles.

Front Wheel

98-02, Suzuki Bergman 250
99-02, Suzuki Bergman 400

SpudRider · 03-21-2017, 02:20 PM

I have confirmed the brake rotor bolts for the first generation, 2007 Kawasaki KLR650, are a perfect match for the RX3 rotor bolts.

Incidentally, these rotor bolts are also employed by the front wheel of my Zongshen ZS200GY-2.

https://www.rockymountainatvmc.com/p...olt-Kit?v=5617

11-18-2015, 02:48 PM	#1
SpudRider Join Date: Jul 2008 Location: Idaho Posts: 25,054	Confirmed Compatible Parts: Zongshen RX3 This thread contains a list of parts from other motorcycles which have been confirmed to fit the Zongshen RX3. This is a closed list. Please contribute your discovery of any parts which fit the Zongshen RX3 in the following thread. http://www.chinariders.net/showthread.php?t=15528 Brake Pads Front Brake Pads: EBC FA185 If you click the following link, you will download the EBC catalog. http://ebcbrakes.com/Assets/ecatalog...Cat.html#p=282 On page 282 you will find the FA185 brake pads. This page lists all the different motorcycles which employ these brake pads. Buy sintered, front brake pads for any of these motorcycles, and they will fit the front brake caliper of your Zongshen RX3. Rear Brake Pads: EBC FA140, EBC FA496 The RX3 motorcycles imported to the United States by CSC have the latest, rear brake caliper. The U.S. bikes use the EBC FA140, EBC FA496 brake pads employed by the following Japanese motorcycles. Honda CB500X, NC700X Triumph Tiger 800 Honda CBR250R, CBR300R, CB300F, CBR650F Suzuki GW250, SFV650 Clutch Parts Here is a list of the Honda motorcycles which employ the same clutch fiber plates, and clutch springs as the Zongshen RX3. Honda XR650L Honda XR600R Honda NX650 Honda CR500R Honda CR480R Honda CR250R It is reported the Honda, clutch metal plates are too thick. Shift Lever The Honda XR650L shift lever is slightly longer than the RX3 shift lever. However, this Honda shift lever, and the many aftermarket shift levers for the Honda XR650L, have a folding tip. The folding tip prevents damage to the shift lever and the engine, should you drop the motorcycle on its left side. Rear Sprocket The JTR473 sprocket is identical to the Zongshen RX3 sprocket for bikes with the rear cushion drive. http://www.jtsprockets.com/catalogue/sprocket/JTR473-40 This sprocket is available with 40T, and 37T. __________________ Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 Last edited by SpudRider; 05-05-2017 at 09:17 AM.
	2

11-18-2015, 03:25 PM	#2
SpudRider Join Date: Jul 2008 Location: Idaho Posts: 25,054	Spark Plug The stock spark plug is a Denso U22ESR-N. Denso spark plugs are somewhat hard to find in the United States. Here is a list of other, equivalent spark plugs. NGK CR7E : Gap 0.031 inches (0.08 mm) Champion RG96C __________________ Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 Last edited by SpudRider; 04-20-2016 at 10:45 PM.
	1

11-19-2015, 03:52 AM	#3
SpudRider Join Date: Jul 2008 Location: Idaho Posts: 25,054	Electrical Connectors Auxiliary Power Plug: Sumitomo, HTW 110 connectors (2-Pin) Headlight Connector: Furukawa, RFW 090 connectors (6-Pin) ECU Diagnostic Port: Furukawa, RFW 090 connectors (6-Pin) __________________ Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894
	0

12-09-2015, 11:05 AM	#4
SpudRider Join Date: Jul 2008 Location: Idaho Posts: 25,054	Throttle Position Sensor (TPS) Delphi SS10459 UPC: 689604104682 5S5008 - AirTex/Wells SS10459 - Delphi __________________ Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 Last edited by SpudRider; 12-29-2015 at 05:01 PM.
	0

12-19-2015, 08:40 PM	#5
SpudRider Join Date: Jul 2008 Location: Idaho Posts: 25,054	Vapor Canister Purge Valve The solenoid purge valve for the evaporative emissions canister is the Delphi 1997278, ACDelco 214-641 unit. http://www.ebay.com/itm/Evaporative-...3D130848197922 __________________ Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894
	0

12-19-2015, 08:42 PM	#6
SpudRider Join Date: Jul 2008 Location: Idaho Posts: 25,054	MAP/MAT Sensor The Delphi 28086011, ACDelco 12232201 MAP sensor is equivalent to the MAP/MAT sensor of the Zongshen RX3. Just make sure you get a 4-pin connector (MAT). It's best if the sensor has a sticker which labels the 4 pins: VOut, 5V, MAT, GND. http://www.ebay.com/sch/sis.html?_nk...p2047675.m4096 __________________ Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894
	0

12-19-2015, 10:37 PM	#7
SpudRider Join Date: Jul 2008 Location: Idaho Posts: 25,054	The following, radiator fan switch is equivalent to the switch employed by the Zongshen RX3. This switch is designed for the following Suzuki and Kawasaki motorcycles. Suzuki GSX-R600 97-05 GSX-R750 96-08 VL/VZ800 01-11 DL1000 V-Strom 03-09 GSX-R1000 01-04 SV1000 03-07 TL1000R/S 98-03 GSX-R1300 “Hayabusa” 99-07 Kawasaki Ninja ZX-6R 2003-2004 ZX636 2003-2004 ZX600 2003-2004 http://www.ebay.com/sch/i.html?_from...witch&_sacat=0 __________________ Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894
	0

04-13-2016, 08:52 AM	#8
SpudRider Join Date: Jul 2008 Location: Idaho Posts: 25,054	Rear Hub Bearing Sizes Rear Hub Bearing, Sprocket Side: 6202 2RS Rear Hub Bearing, Brake Rotor Side: 6302 2RS Sprocket Carrier Bearing: 6004 2RS Front Hub Bearing Sizes (2) 6302 2RS __________________ Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894
	3

03-21-2017, 06:28 AM	#9
SpudRider Join Date: Jul 2008 Location: Idaho Posts: 25,054	I have verified the EBC, MD929D brake rotor is a perfect fit for the front wheel of the Zongshen RX3. This brake rotor fits the following motorcycles. Front Wheel 98-02, Suzuki Bergman 250 99-02, Suzuki Bergman 400 __________________ Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894
	4

03-21-2017, 02:20 PM	#10
SpudRider Join Date: Jul 2008 Location: Idaho Posts: 25,054	I have confirmed the brake rotor bolts for the first generation, 2007 Kawasaki KLR650, are a perfect match for the RX3 rotor bolts. Incidentally, these rotor bolts are also employed by the front wheel of my Zongshen ZS200GY-2. https://www.rockymountainatvmc.com/p...olt-Kit?v=5617 __________________ Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894
	0