My Bashan BSR250 arrived! - Page 2

da4design · 01-18-2018, 07:36 PM

nice looking bike, making me think about getting one!

letsride · 01-18-2018, 07:39 PM

You need to warm it up and adjust the idle, using the idle adjustment screw on the side of the carb. Now I can't remember which position of the choke lever is ON! Someone will be along shortly to answer. I think DOWN is ON! if I remember right.

MacGregor · 01-18-2018, 09:48 PM

Quote:

Originally Posted by letsride

You need to warm it up and adjust the idle, using the idle adjustment screw on the side of the carb. Now I can't remember which position of the choke lever is ON! Someone will be along shortly to answer. I think DOWN is ON! if I remember right.

I had to turn the screw in about 2 1/2 turns for it to idle with the choke lever up, however the lever down causes it too idle way high. I took it for a quick ride and it sputters on acceleration (it didn't before). I don't want to do any more until I get the oil changed, so I'll do that shortly and save the rest for tomorrow.

**JerryHawk250** · 01-18-2018, 10:10 PM

Quote:

Originally Posted by letsride

Great Progress! Can't wait to see some pitchers! What color is the thing? I'm trying to find the original "Enforcer" Thread of (I think) the first to guys to purchase and document them here.

You really should get your eyes checked.

**JerryHawk250** · 01-18-2018, 10:11 PM

Bike looks great.

**JerryHawk250** · 01-18-2018, 10:13 PM

Quote:

Originally Posted by MacGregor

I had to turn the screw in about 2 1/2 turns for it to idle with the choke lever up, however the lever down causes it too idle way high. I took it for a quick ride and it sputters on acceleration (it didn't before). I don't want to do any more until I get the oil changed, so I'll do that shortly and save the rest for tomorrow.

Chock lever all the way up is on and all they way down is off. Adjust the idle with the chock off.

Weldangrind · 01-19-2018, 12:04 PM

Nice looking bike! Thanks for the pics.

Quote:

Originally Posted by MacGregor

The spring for the kickstand is a bit tricky. I used a screwdriver, which worked well.

As a tip for the next China Rider to install a kickstand spring, insert several washers or coins between the coils of the spring. That will expand it to a length that makes it easy to install without producing any blood.

Megadan · 01-19-2018, 01:48 PM

Quote:

Originally Posted by Weldangrind

Nice looking bike! Thanks for the pics.

As a tip for the next China Rider to install a kickstand spring, insert several washers or coins between the coils of the spring. That will expand it to a length that makes it easy to install without producing any blood.

I can second the coin trick, having used it before. Another option is a good old fashioned drum brake spring tool. It is literally designed for this exact type of work - to install small stiff springs on spring studs with rounded ends. Makes it a breeze.

MacGregor · 01-19-2018, 05:25 PM

Quote:

Originally Posted by da4design

nice looking bike, making me think about getting one!

The assembly wasn't bad at all. I would probably recommend buying from a different retailer than where I got mine, but overall I'm very happy with it.

MacGregor · 01-19-2018, 05:27 PM

Quote:

Originally Posted by JerryHawk250

Chock lever all the way up is on and all they way down is off. Adjust the idle with the chock off.

Thanks, I think that may have worked. I let it warm up first then adjusted it. Just went around the block a few times. No sputtering at all. It's got a bit of grunt for a little 250.

MacGregor · 01-19-2018, 05:30 PM

Just a note - the handlebars and grips are aftermarket. I got the Tusk Chub bars with the YZ bend. For reference, these were pretty close to the bend of the stock bars (the Chubs are about 1" longer on each end, with slightly less pullback. Rise is about the same.)

**JerryHawk250** · 01-19-2018, 07:16 PM

Quote:

Originally Posted by MacGregor

Thanks, I think that may have worked. I let it warm up first then adjusted it. Just went around the block a few times. No sputtering at all. It's got a bit of grunt for a little 250.

It only gets better as it breaks in. A free flowing exhaust and carb tuning it gets even better. These are fun bikes to play around with and not cost an arm and a leg. Lol

Megadan · 01-19-2018, 07:49 PM

Quote:

Originally Posted by JerryHawk250

It only gets better as it breaks in. A free flowing exhaust and carb tuning it gets even better. These are fun bikes to play around with and not cost an arm and a leg. Lol

Or a quick and easy head porting job.

MacGregor · 01-19-2018, 08:02 PM

Quote:

Originally Posted by JerryHawk250

It only gets better as it breaks in. A free flowing exhaust and carb tuning it gets even better. These are fun bikes to play around with and not cost an arm and a leg. Lol

I'm planning on doing the eBay exhaust and rejet. I'll probably leave the gearing stock, but replace the chain.

01-18-2018, 07:39 PM	#17
letsride Join Date: Oct 2013 Location: Leesville SC Posts: 835	You need to warm it up and adjust the idle, using the idle adjustment screw on the side of the carb. Now I can't remember which position of the choke lever is ON! Someone will be along shortly to answer. I think DOWN is ON! if I remember right. __________________ My Stable- 2022 Lifan KPX250 , 2023 Royal Enfield Himalayan, 1992 Honda GL1500 Goldwing, SSR 70 Auto, Kymco Mongoose 90, Honda Four Trax 300
	0

01-18-2018, 10:11 PM	#20
JerryHawk250 Moderator Join Date: Oct 2016 Location: Houma, La. Posts: 11,738	Bike looks great. __________________ 2024 Linhai 300 ATV 4x4 2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S (Sold) 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel
	0

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-18-2018, 07:36 PM	#16
da4design Join Date: Mar 2017 Location: texas Posts: 253	nice looking bike, making me think about getting one!
	1

01-19-2018, 05:30 PM	#26
MacGregor Join Date: Jan 2018 Posts: 21	Just a note - the handlebars and grips are aftermarket. I got the Tusk Chub bars with the YZ bend. For reference, these were pretty close to the bend of the stock bars (the Chubs are about 1" longer on each end, with slightly less pullback. Rise is about the same.)
	0