12-14-2013, 03:57 AM | #16 |
Join Date: Jun 2009
Location: Brisbane, Queensland, Australia
Posts: 648
|
she s not looking bad at all, mate! good work!
the carbie looks like a keihin copy but i may be wrong. what sort and size of main jet do you have? does an oil breather fit below the carbie and the crankcase venthole? that would look neat.
__________________
1971 Garelli Gulp 50cc with open ports and 16 mm Bing Carbie + 1980 Honda XL 223 ZS + 2007 Zongshen LZX200G + DR400SM |
|
12-14-2013, 04:27 AM | #17 |
Join Date: Oct 2013
Posts: 32
|
Don't know what size the standard jets are, I've just adjusted the idle fuel mixture and it seems to be running fine for short trips are my area.
I've got a small filter that I'll try and fit up for the crankcase breather soon |
|
12-14-2013, 04:35 AM | #18 |
Join Date: Jun 2009
Location: Brisbane, Queensland, Australia
Posts: 648
|
with that air filter you ll probably run lean at full throttle
__________________
1971 Garelli Gulp 50cc with open ports and 16 mm Bing Carbie + 1980 Honda XL 223 ZS + 2007 Zongshen LZX200G + DR400SM |
|
12-14-2013, 05:45 AM | #19 |
Join Date: Oct 2013
Posts: 32
|
Good to know, thanks.
Jets will be looked at in the near future. |
|
12-14-2013, 06:46 AM | #20 |
Join Date: Jun 2009
Location: Brisbane, Queensland, Australia
Posts: 648
|
lifting the needle one notch, ie moving the needleclip one down does make a difference, if you haven t done that.
__________________
1971 Garelli Gulp 50cc with open ports and 16 mm Bing Carbie + 1980 Honda XL 223 ZS + 2007 Zongshen LZX200G + DR400SM |
|
12-18-2013, 03:32 AM | #21 |
Join Date: Oct 2013
Posts: 32
|
|
|
12-18-2013, 03:33 AM | #22 |
Join Date: Oct 2013
Posts: 32
|
Anyone know what the intake & exhaust valve clearance are suppose to be set to?
|
|
12-18-2013, 03:43 AM | #23 | |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
Quote:
You might find the valve lash information you seek in the following thread. http://www.chinariders.net/showthread.php?t=977
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
|
12-18-2013, 05:41 AM | #24 |
Join Date: Mar 2008
Posts: 2,436
|
That's a MD33 clone.
authorized Honda dealer in Japan http://www.ride-inc.net/file/32/data.pdf
__________________
|
|
12-18-2013, 10:23 AM | #25 | |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Quote:
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
|
12-18-2013, 10:26 AM | #26 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
That is a sweet looking little bike. If you're looking for more power, there's some hiding in that catalytic converter. Removing it would require larger jets.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
12-18-2013, 02:28 PM | #27 |
Join Date: Oct 2013
Posts: 32
|
Thanks HB, I'll try and work it out from the link.
|
|
12-18-2013, 05:50 PM | #29 |
Join Date: Jun 2009
Location: Brisbane, Queensland, Australia
Posts: 648
|
stellio, i ve looked it up for my 233 engine before:
OHC motor, no pushrods. According to Honda dealer in Japan http://www.ride-inc.net/file/32/data.pdf MD33 (65.5mm x 66.2 mm) IN/EX = 0.1mm (0.004 inches) small problem was that the flywheel didn t have a TDC marking on it. maybe yours does have one. of course one can judge from the piston. but i eventually took the left case off, and made a marking for TDC on the flywheel.
__________________
1971 Garelli Gulp 50cc with open ports and 16 mm Bing Carbie + 1980 Honda XL 223 ZS + 2007 Zongshen LZX200G + DR400SM |
|
12-18-2013, 08:45 PM | #30 |
Join Date: Oct 2013
Posts: 32
|
Thanks mate.
|
|
|
|
Thread Tools | Search this Thread |
Display Modes | |
|
|