|
|
|
|
Thread Tools | Search this Thread | Display Modes |
|
04-09-2011, 08:32 PM | #1 |
Join Date: Oct 2009
Location: Alberta, Canada
Posts: 3,274
|
Fingers crossed that I fixed my fork seal leak... Hopefully!
I had a weeping seal on my front left fork. It started leaking at only 2400 km's. Never had one konk out that quick before! I bought a set of new seals online, All Balls brand, but after reading a few reviews it seems people have had a lot of problems with the All Balls seals so I was reluctant to install them. At the suggestion of people here and on the KLR forum I decided to try to clean the seal with a SealMate.
I pulled the boot up and slid up the wiper to use the seal saver and found what I think was causing my leak... The fork tube had a tiny little mark in it. Almost like a little pit or nick, but you could catch your fingernail on it. Pretty sure that was causing the problem. I'm guessing that the seal is damaged and will need replaced anyway, but I got some superfine wet/dry sandpaper and gingerly polished out the nick until it felt smooth and no longer catches your nail. Then I ran the SealMate around the tube twice to clean the seal lip and pumped the forks 20 or so times... No leaks!! I'm guessing that I'll have to change out the seals anyway, but at least I think I found the problem. Not leaking right now so I'll keep a close eye on it. Funny part is, why would the fork have a nick in the tube? The bike has boots on the forks so no gravel hits them and it's only 3 years old now with low mileage. Guess maybe it was like that since manufacture? So, I'm impressed with the SealMate and if the fork doesn't leak anymore I will be very happy! Now, to just be able to find the time to ride... Cheers, Stew |
|
04-09-2011, 10:10 PM | #2 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
That's good news. I'm not sure what SealMate is; can you describe it?
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
04-09-2011, 10:23 PM | #3 | |
Join Date: Oct 2009
Location: Alberta, Canada
Posts: 3,274
|
Quote:
I've talked to people that have had great success with them, so I'm hoping if my seals not cut up by the nick that it did the trick. Cheers, Stew |
|
|
04-09-2011, 10:50 PM | #4 |
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
|
Excellent! Thanks for the link. The video was very convincing.
Glad to see they come in Honda red.
__________________
Weldangrind "I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer |
|
04-09-2011, 11:28 PM | #5 |
Join Date: Jan 2011
Location: Jamestown, PA
Posts: 589
|
Sweet - That was educational. I will definately remember that one. The tool is pretty cool, but I'm sure we all have some material laying around to FAB up our own. Then again for $5 I'd probably buy some to throw in the toolbox. - Thanks for sharing the link....
__________________
Andrew - Jamestown, PA 16134 YouTube Videos: http://www.youtube.com/user/Jtcomp2009#p/u 2009 Qlink XF200 Supermoto 1982 Honda CM200 Bobber - SOLD 2003 JEEP Liberty SPORT = 3" Lift 2002 Chevy Trailblazer LTZ - Family Cruiser |
|
04-09-2011, 11:50 PM | #6 |
Join Date: Oct 2009
Location: Alberta, Canada
Posts: 3,274
|
I've also been told that you can use a feeler gauge held at an angle, but you have to be careful not to cut the seal with the sharp feeler gauge. I was going to try the film trick but I couldn't find any 35mm negatives laying around . When I ordered mine they sent a spare so I got two for the price of one. I might end up replacing the seals anyway if the nick cut it, but wanted to give this a shot anyway.
Cheers, Stew |
|
04-10-2011, 01:26 AM | #7 |
Join Date: Jul 2008
Location: Idaho
Posts: 25,054
|
I'm glad you fixed the problem, Stew! To clean the grit from my oil seals I have used a feeler gauge, and paint sample strips I obtained from Lowes. Some riders employ business cards for the same purpose. As with you, I don't know where I would obtain any 35 mm film negatives! 8O The Seal Saver looks like a great tool. However, as a China Rider, I'm too frugal, i.e. cheap, to buy one. :roll:
Spud
__________________
Spud "Never argue with an idiot. He will drag you down to his level, and beat you with experience." Mark Twain 2015 Zongshen ZS250GY-3 (RX3) 2006 Zongshen ZS200GY-2 (Sierra 200) 2005 Honda XR650L 2004 Honda CRF250X 1998 Kawasaki KDX220 Mods made to my Zongshen ZS200GY-2: http://www.chinariders.net/showthread.php?t=6894 |
|
|
|
|
|