|
05-15-2018, 07:12 PM | #1 |
Join Date: Apr 2018
Location: Milford, IN
Posts: 27
|
Tuning and jetting hawk 250
Ok so first let me begin by saying I'm sorry for this question that has probably been asked a million times, but I'm trying to figure this out. I bought the mikuni carb on Amazon and a pack of jets. I live in Indiana at approximately 800ft above sea level. I have a stock exhaust and have done the air box mod. Can someone tell me how to tune my carb and what jet to install to start with????? My hawk runs great until 3/4 throttle then it really bogs down. I'm sick of it running like crap and can't wait any longer to get the new carb on.
__________________
2017 Hawk 250 2007 Honda VTX1300R 2016 Kawasaki Vulcan Voyager |
|
05-15-2018, 09:55 PM | #2 |
Join Date: Apr 2017
Location: Omaha, NE
Posts: 8,100
|
Jetting recommendations with an airbox mod and stock exhaust on the Mikuni clone at your altitude.
Main Jet, 110 Pilot jet 25 (recommend also buying a 27.5) Needle set at 4th notch from the top/1 down from center. Idle mixture, start 1 1/2 turns out from lightly seated. This will get you very close, but obviously fine tunibg may be needed to get your bike ideally jetted.
__________________
Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 2024 Royal Enfield Shotgun 650 https://chinariders.net/showthread.php?t=34124 |
|
05-09-2020, 02:32 PM | #3 | |
Join Date: Apr 2020
Location: Atlanta, GA
Posts: 58
|
Quote:
But, holy cow what a difference. After gas got into the bowl it immediately idled and I've set the idle speed pretty low (i'm guessing by sound as I dont have anything to measure with) Still waiting for paperwork so I can actually take it out of the neighborhood but very pleased. Also replaced the stock shifter with the one everyone recommends and very pleased with it. |
|
|
05-09-2020, 02:47 PM | #4 | |
Join Date: Apr 2017
Location: Omaha, NE
Posts: 8,100
|
Quote:
Glad it worked out well for you.
__________________
Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 2024 Royal Enfield Shotgun 650 https://chinariders.net/showthread.php?t=34124 |
|
|
05-16-2018, 05:22 AM | #5 |
Join Date: Apr 2018
Location: Milford, IN
Posts: 27
|
What pilot jet typically comes stock with the mikuni?
__________________
2017 Hawk 250 2007 Honda VTX1300R 2016 Kawasaki Vulcan Voyager |
|
05-16-2018, 06:55 AM | #6 |
Join Date: Feb 2018
Location: nashville
Posts: 574
|
both my vm26 came with 20 pilot
|
|
05-16-2018, 07:21 AM | #7 |
Join Date: Mar 2018
Location: Northern Maine
Posts: 55
|
when I got my Mikuni I put in a 110. I got the wrong pilot jet so I left it stock. Just put in a 25 and now the bike runs great.
I am at 400 feet. running a 110 and a 25. everything else stock. Mixture screw out 1 1/2 turns. |
|
05-16-2018, 10:46 AM | #8 |
Join Date: Apr 2017
Location: Omaha, NE
Posts: 8,100
|
THe Mikuni comes with a 100 main and 20 pilot (as imapdog stated).
If you want to order genuine jets, which I highly recommend, then your part numbers are; Main: N100.604 - https://www.jetsrus.com/a_jets_by_ca...arge_round.htm Pilot: VM28/486 - https://www.jetsrus.com/a_jets_by_ca...-486_pilot.htm
__________________
Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 2024 Royal Enfield Shotgun 650 https://chinariders.net/showthread.php?t=34124 |
|
05-17-2018, 03:48 PM | #9 |
Join Date: Apr 2018
Location: Milford, IN
Posts: 27
|
Thanks guys I really appreciate it. I ordered the pilot jets yesterday from rocky mountain atv 2 day shipping. Fingers crossed that they get here so I can get this thing fixed up saturday morning.
__________________
2017 Hawk 250 2007 Honda VTX1300R 2016 Kawasaki Vulcan Voyager |
|
05-17-2018, 08:01 PM | #10 |
Join Date: May 2018
Posts: 64
|
Yeah I ordered a bunch of jets from Rocky and got the mikuni carb today. Drilled the stock jet somewhere between 105 and 110, shimmed the needle 3 washers and have some mid throttle bogging. Funny enough around 50mph I can go full throttle and really get a good pull. Spark plug sooty. Wondering if it's valve lash?
|
|
05-17-2018, 09:28 PM | #11 | |
Join Date: Apr 2017
Location: Omaha, NE
Posts: 8,100
|
Quote:
__________________
Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 2024 Royal Enfield Shotgun 650 https://chinariders.net/showthread.php?t=34124 |
|
|
05-17-2018, 08:02 PM | #12 |
Join Date: May 2018
Posts: 64
|
Not to hijack thread just seems like good place. :-)
|
|
05-17-2018, 09:39 PM | #13 |
Join Date: May 2018
Posts: 64
|
Oops, I worded badly. Shimmed the stock carb and mikuni came after. I had already ordered the mikuni and jets I was just doing trial and error on the stock carb. Also, the bike has eBay exhaust and it's changing colors. Airbox also modified with cutout. I love the bike. Just a few minor tuning issues. My test run was a 20 mile trip to BMV so I could register. 1-2-3 shifts from stop are tricky because of bogging issues.
|
|
05-18-2018, 11:30 AM | #14 | |
Join Date: Apr 2017
Location: Omaha, NE
Posts: 8,100
|
Quote:
I would suggest maybe stepping up to a 115 main jet with that exhaust installed, especially if you have an intake modification of some kind. What size pilot jet are you running?
__________________
Hawk Information and Resource guide: http://www.chinariders.net/showthread.php?t=20331 2018 Hawk 250 - Full Mod list here. http://www.chinariders.net/showpost....62&postcount=1 2024 Royal Enfield Shotgun 650 https://chinariders.net/showthread.php?t=34124 |
|
|
05-18-2018, 06:42 PM | #15 |
Join Date: May 2018
Posts: 64
|
OK so jets came in today I'll switch to new carb and try 25 and 115. I have jets to go smaller/bigger by 2.5 or more. Mixture screw should be one and a half turn? And to answer your question I hadnt tried drilling the original pilot jet just did the main.
|
|
|
|
|
|