My Brozz just showed up

Kipper1012 · 04-05-2017, 03:55 PM

Whoooooo

But there is some damage on the rear grab bar and the gas tank

I've already sent them a email about it. The grab bar I'm not too concerned about but the gas tank and fuel cap I want to get replaced

Kipper1012 · 04-05-2017, 03:56 PM

Also I went to immediately remove the decals after taking the crate apart and it looks as though the decals have been clear coated on to the plastics

Not sure if it will do damage the plastics trying to remove them or if it will leave unsightly lines

Ski_rush · 04-05-2017, 04:32 PM

I think my decals are the same as yours. I used a heat gun and all but one came right off very smoothly. However, one peeled the red off the plastic in one small spot. I'll probably just use touch up paint for that or slap a small decal there...Haven't decided.

Use a heat gun. Makes it much easier.

**JerryHawk250** · 04-05-2017, 04:36 PM

Quote:

Originally Posted by Ski_rush

I think my decals are the same as yours. I used a heat gun and all but one came right off very smoothly. However, one peeled the red off the plastic in one small spot. I'll probably just use touch up paint for that or slap a small decal there...Haven't decided.

Use a heat gun. Makes it much easier.

Wait... the Enforce has painted plastic? The Hawk is just colored plastic. That might be why mine was so easy to take off.

**JerryHawk250** · 04-05-2017, 04:38 PM

Glad you got your Brozz but sucks that it came damaged.

Ski_rush · 04-05-2017, 05:19 PM

Quote:

Originally Posted by JerryHawk250

Wait... the Enforce has painted plastic? The Hawk is just colored plastic. That might be why mine was so easy to take off.

I'm assuming so. Left side decals peeled right off without a problem. There was just one spot on the right side where, as I was peeling the sticker off, red paint came with it and it was white underneath. And the decal wasn't like a normal sticker. It was really thick, like he said, clear coated, almost like a clear coat over a decal.

I don't like the "BSR" logo on my bike and will be taking it off. That's the decal that "stuck". However, I liked the white mark from the peeled paint even worse, so I just laid the lame BSR decal back in place for now until I figure out what I will put in it's place.

dubbya1986 · 04-05-2017, 05:04 PM

Quote:

Originally Posted by Kipper1012

Whoooooo

But there is some damage on the rear grab bar and the gas tank

I've already sent them a email about it. The grab bar I'm not too concerned about but the gas tank and fuel cap I want to get replaced

Be vigilant man. I would honestly call as soon as you send the email and make sure they get get on getting those parts to you right away. It seemed that talking to them directly vs emailing got me my missing mirror vs email. Glad to see it arrived for you.

chuck · 04-05-2017, 05:05 PM

Quote:

Originally Posted by Kipper1012

Whoooooo

But there is some damage on the rear grab bar and the gas tank

I've already sent them a email about it. The grab bar I'm not too concerned about but the gas tank and fuel cap I want to get replaced

They are handling these crates with no care for the customer and most times they get away with it.It just piss me off.

Kipper1012 · 04-05-2017, 05:25 PM

My decals have no Edge you can feel with your fingernail like the whole plastic has several coats of clear coat over the decal making the transition at the edge of the decal very smooth.

2LZ · 04-05-2017, 05:33 PM

Quote:

Originally Posted by Kipper1012

My decals have no Edge you can feel with your fingernail like the whole plastic has several coats of clear coat over the decal making the transition at the edge of the decal very smooth.

Unless a person hates decals, that's the proper way to do stick-on striping and decals.

goat67 · 04-05-2017, 07:01 PM

Man that sucks mine was shipped by R&L also I know I will never use them if I have a choice.

Who did you buy this from?

Kipper1012 · 04-05-2017, 07:45 PM

Quote:

Originally Posted by goat67

Man that sucks mine was shipped by R&L also I know I will never use them if I have a choice.

Who did you buy this from?

Superior power sports

goat67 · 04-05-2017, 07:49 PM

Quote:

Originally Posted by Kipper1012

Superior power sports

File a damage claim it is on their site and then give them a call. I had a damage claim and they did get a part out to me.

Xerxes.1.14 · 04-05-2017, 05:31 PM

R&L huh, My Shark is a day away and it was shipped by R&L from PSM. Here hoping I dont get anything damaged.
However a tank is much easier to replace than the gentleman who got a messed up frame.

da4design · 04-05-2017, 07:04 PM

glad you got it, sorry for the damage though. hope they replace all the damage asap and you can enjoy building it!

04-05-2017, 03:55 PM	#1
Kipper1012 Join Date: Mar 2017 Location: Florida Posts: 198	My Brozz just showed up Whoooooo But there is some damage on the rear grab bar and the gas tank I've already sent them a email about it. The grab bar I'm not too concerned about but the gas tank and fuel cap I want to get replaced __________________ 2016 Green Bashan Brozz.
	0

04-05-2017, 03:56 PM	#2
Kipper1012 Join Date: Mar 2017 Location: Florida Posts: 198	Also I went to immediately remove the decals after taking the crate apart and it looks as though the decals have been clear coated on to the plastics Not sure if it will do damage the plastics trying to remove them or if it will leave unsightly lines __________________ 2016 Green Bashan Brozz.
	0

04-05-2017, 04:38 PM	#5
JerryHawk250 Moderator Join Date: Oct 2016 Location: Houma, La. Posts: 11,723	Glad you got your Brozz but sucks that it came damaged. __________________ 2024 Linhai 300 ATV 4x4 2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S (Sold) 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel
	1

04-05-2017, 05:25 PM	#9
Kipper1012 Join Date: Mar 2017 Location: Florida Posts: 198	My decals have no Edge you can feel with your fingernail like the whole plastic has several coats of clear coat over the decal making the transition at the edge of the decal very smooth. __________________ 2016 Green Bashan Brozz.
	0

04-05-2017, 05:31 PM	#14
Xerxes.1.14 Join Date: Mar 2017 Posts: 16	R&L huh, My Shark is a day away and it was shipped by R&L from PSM. Here hoping I dont get anything damaged. However a tank is much easier to replace than the gentleman who got a messed up frame. __________________ 2008 Kawasaki Versys 650 - sold 2016 Bashan Shark 250- sold but still in the family 2020 KTM Duke 390 2005 Yamaha Roadstar 2021 Hawk 250
	1

04-05-2017, 04:32 PM	#3
Ski_rush Join Date: Feb 2017 Posts: 449	I think my decals are the same as yours. I used a heat gun and all but one came right off very smoothly. However, one peeled the red off the plastic in one small spot. I'll probably just use touch up paint for that or slap a small decal there...Haven't decided. Use a heat gun. Makes it much easier.
	0

04-05-2017, 07:01 PM	#11
goat67 Join Date: Mar 2017 Location: Twin Cities MN Posts: 525	Man that sucks mine was shipped by R&L also I know I will never use them if I have a choice. Who did you buy this from?
	0

04-05-2017, 07:04 PM	#15
da4design Join Date: Mar 2017 Location: texas Posts: 253	glad you got it, sorry for the damage though. hope they replace all the damage asap and you can enjoy building it!
	0