Oil cooler install

[JerryHawk250]

My oil cooler finally came in today. It took me about an hour to install. After I installed the cooler I added oil with the provided syringe. I cranked it up to prime the oil lines and checked the oil level and added a little more oil. I took a ride down the road and came back and check the oil again. A check valve is not needed if you connect the line out from the engine to the bottom of the cooler. I let it set for an hour and the oil didn't drain back to the engine. I'll have to shorten the line with the filter when I get a chance.

Addition info: I used a piece of 1" angle iron using the two motor mount bolts at the bottom . After I mounted I realized I could flip the cooler mounting bracket and will set the cooler further back and the oil lines will be behind the angle iron. I'll take care of that and post pictures when I get to it.

[JeremyC]

Looks good! Is that one from mj? I'll get one eventually.
On a side note, if you tweak that wire retainer for your front brake line, you can get it to go inside of both of those ridges on that rubber insulator. It takes some judicious bending and squeezing with pliers. My OCD made me do it!

[JerryHawk250]

Originally Posted by JeremyC

Looks good! Is that one from mj? I'll get one eventually.
On a side note, if you tweak that wire retainer for your front brake line, you can get it to go inside of both of those ridges on that rubber insulator. It takes some judicious bending and squeezing with pliers. My OCD made me do it!

Thanks . No I got it on taobao.com $54 and some change delivered. I originally ordered with a stack plate cooler but was out of stock. https://world.taobao.com/item/254075...?fromSite=main

[dpl096]

I agree...looks great. Well done indeed

[mjstef]

Originally Posted by JerryHawk250

Thanks . No I got it on taobao.com $54 and some change delivered. I originally ordered with a stack plate cooler but was out of stock. https://m.intl.taobao.com/detail/det...id=25407512835

Yup, To the point it's cheaper 1 at a time with shipping than in bulk as China post small items are pretty cheap to ship. I got 6 of the valve cover coolers in with the stacked plate coolers and shipping alone was $129 usd. My wholesale price with shipping in bulk is more than you paid. Still waiting on seeing if they can come up with an UNCRIMPED end on one hose but haven't heard back.

On your routing, Not sure it make a lot of difference on a bike but on cars, Trucks, Heavy equipment and hydraulic systems the hot (out) line always goes to the top as heat rises and if it went into the bottom the cooler/radiator efficiency is compromised. Just food for thought..........

[Merlin]

Originally Posted by mjstef

On your routing, Not sure it make a lot of difference on a bike but on cars, Trucks, Heavy equipment and hydraulic systems the hot (out) line always goes to the top as heat rises and if it went into the bottom the cooler/radiator efficiency is compromised. Just food for thought..........

That's the way I have it.

[JerryHawk250]

Originally Posted by Merlin

That's the way I have it.

Post some pictures of your install. If I remember right you had installed a check valve on yours. It will work that way just have to make sure that the cooler is filled completely with oil so that air will not get trapped in the cooler. But I know you knew that already. It was nice that they supplied a syringe with the kit to do that.

[JerryHawk250]

Originally Posted by mjstef

On your routing, Not sure it make a lot of difference on a bike but on cars, Trucks, Heavy equipment and hydraulic systems the hot (out) line always goes to the top as heat rises and if it went into the bottom the cooler/radiator efficiency is compromised. Just food for thought..........

That's the way it should be, but without the check valve the oil will drain back into the block. I haven't checked it today, but when I get home this afternoon I'll see if it drained back or not. If it did then I'll get a check valve. Another reason for feeding it from the bottom is so it doesn't get air bound. Feeding from the bottom will force the air out the top. If feed from the top and air is trapped at the top and the cooler will never completely fill with oil. Mounted horizontally with the connections on top is the ideal way it should be mounded. I had it mounded that way and put a 1" plastic spacer on the fender to lower it. The fender cleared the cooler but I didn't like the idea of the fender blocking the air flow across the cooler. The crimped end look nice but one end on each line should be left uncrimped so you can custom fit the lines. I was planning on buying a cooler from you but I wanted to get one before this weekend coming. We had planned on going on a off road trip over the weekend but looks like that may change due to rain.

[JerryHawk250]

Originally Posted by mjstef

Yup, To the point it's cheaper 1 at a time with shipping than in bulk as China post small items are pretty cheap to ship. I got 6 of the valve cover coolers in with the stacked plate coolers and shipping alone was $129 usd. My wholesale price with shipping in bulk is more than you paid. Still waiting on seeing if they can come up with an UNCRIMPED end on one hose but haven't heard back. .

Matt,
Just send the units out with a check valve that way when installing the check valve the length could be adjusted then.

[MDStroup]

Originally Posted by JerryHawk250

Thanks . No I got it on taobao.com $54 and some change delivered. I originally ordered with a stack plate cooler but was out of stock. https://world.taobao.com/item/254075...?fromSite=main

Do you have the link to the version of the oil cooler with the stacked plate cooler?

Also, did any one else have a problem having the page from the link no translating?

[JerryHawk250]

Originally Posted by MDStroup

Do you have the link to the version of the oil cooler with the stacked plate cooler?

Also, did any one else have a problem having the page from the link no translating?

Contact mjstef hawkclusters@gmail.com for the stack plate. He has the valve cover kit with the stack plate cooler and I think he is working on getting the oil screen version like my kit with the stack plate too.
View the TaoBao site with Google Chrome to translate it.

[MDStroup]

Originally Posted by JerryHawk250

Contact mjstef hawkclusters@gmail.com for the stack plate. He has the valve cover kit with the stack plate cooler and I think he is working on getting the oil screen version like my kit with the stack plate too.
View the TaoBao site with Google Chrome to translate it.

Thanks.

All i use on this PC is chrome and every time i translated it it would stay the same.

[redneck51587]

Originally Posted by JerryHawk250

Thanks . No I got it on taobao.com $54 and some change delivered. I originally ordered with a stack plate cooler but was out of stock. https://world.taobao.com/item/254075...?fromSite=main

How do you order from this site if you can't read chinese?? Asking for a friend... LOL

[JerryHawk250]

Originally Posted by redneck51587

How do you order from this site if you can't read chinese?? Asking for a friend... LOL

Open with Google Chrome. It will translate it for you.

[BBOWL10]

Originally Posted by JerryHawk250

Thanks . No I got it on taobao.com $54 and some change delivered. I originally ordered with a stack plate cooler but was out of stock. https://world.taobao.com/item/254075...?fromSite=main

JerryHawk250,
Did you pay direct to them with your credit card? I went through the whole set up process and they confirmed the order. There is a tab to click for payment but it is not a PayPal link but it looks similar to PayPal. When I click it, it immediately asks for my CC info when usually it would direct me to PayPal and then back to the merchant. I don't feel comfortable giving out my info to an offshore merchant. Seems fishy to me. Please advise. I also sent you a PM