Risers?

[SpudRider]

Originally Posted by jbfla

Motorcycle Handlebar Risers (28.6mm) 34 USD

...plus shipping to your location.

The shipping is by weight. The shipping for my order of the kickstand foot and crash guard protectors was $28. US

jb

Thanks, JB.

[RedHawk47]

Originally Posted by jbfla

It seems I always have a slightly different experience than everyone else.

When I installed the Tusk 30mm 1 1/8" risers, I could not center the handlebars because the throttle and brake lines were too tight.

I moved the throttle cable and brake line outside the plastic shroud surrounding the ignition key, and all was good.



jb

What handlebar guards are those? What size clamp did you get for the inner clamp?

[rjmorel]

Originally Posted by SpudRider

How much does Yoo charge for the handlebar risers, JB?

"1.Kickstand 38 USD
2.RUBBER SLIDERS CRASH PROTECTOR 24USD for set.
3.Motorcycle Handlebar Risers (28.6mm) 34 USD
4.ACERBIS Hand guards+SUPPORT +ADD-ON SPOILERS 45 USD
5.Smoke Windshield 42 USD"

FROM #87 of
http://www.chinariders.net/showthrea...t=15456&page=6

rj

[jbfla]

Originally Posted by RedHawk47

What handlebar guards are those? What size clamp did you get for the inner clamp?

Tusk handguards with modified 7/8" inch clamps.

But there is more to the story:

http://www.chinariders.net/showthread.php?t=15860

jb

[Aleong1967]

That's the same stuff that I ordered

[jbfla]

Originally Posted by Aleong1967

That's the same stuff that I ordered

Did you have to relocate the cables when you installed the risers?

jb

[Aleong1967]

Have not tried them yet
My bike has not arrived yet
But from what the seller told me, not issues with the cable lengths

[keithmaine]

How much does Yoo handlebar risers actually raise the bars and how far is the offset?
I have the Tusk riser but I would like the same height but moved back a bit. I may order them along with yoo windshield

[AdventureDad]

So, just to confirm, the Tusk risers need to be 1/18th in size? and as far as the tusk wraparound handguards, is there enough clearance so it doesn't hit anything that is plugged into the accessory socket or usb socket? I figured I could add spacers to the end of the handlebar to bring it further out for clearance.

[SpudRider]

Originally Posted by AdventureDad

So, just to confirm, the Tusk risers need to be 1/18th in size? and as far as the tusk wraparound handguards, is there enough clearance so it doesn't hit anything that is plugged into the accessory socket or usb socket? I figured I could add spacers to the end of the handlebar to bring it further out for clearance.

Yes, you need the 1-1/8" handlebar risers.

I shortened the bars on my Tusk D-Flex hand guards. With the Tusk Handlebar Risers installed, I have clearance with the power outlets. However, I don't know if placing spacers on the ends of the handlebars will provide enough clearance with the power outlets.

[yarimurray]

Originally Posted by rjmorel

"1.Kickstand 38 USD
2.RUBBER SLIDERS CRASH PROTECTOR 24USD for set.
3.Motorcycle Handlebar Risers (28.6mm) 34 USD
4.ACERBIS Hand guards+SUPPORT +ADD-ON SPOILERS 45 USD
5.Smoke Windshield 42 USD"

FROM #87 of
http://www.chinariders.net/showthrea...t=15456&page=6

rj

Do you have pictures of the rubber crash guard sliders? I'm going to order the kickstand pad (and possibly some of the the carbon kevlar pieces) so I might be interested in these.

Thanks,

Mike

[yarimurray]

Originally Posted by jbfla

It seems I always have a slightly different experience than everyone else.

When I installed the Tusk 30mm 1 1/8" risers, I could not center the handlebars because the throttle and brake lines were too tight.




I moved the throttle cable and brake line outside the plastic shroud surrounding the ignition key, and all was good.





jb

What is the black piece around the fuel cap in that last picture? Also, do I see some sort of kevlar guard on the tank? I'm curious about these pieces.

[jbfla]

Originally Posted by yarimurray

What is the black piece around the fuel cap in that last picture? Also, do I see some sort of kevlar guard on the tank? I'm curious about these pieces.

Around the fuel filler is a mount for a Bags Connection Micro tank bag.

Not a very large bag, just big enough for keys, sunglasses, phone, earplugs, etc.



On the rear part of the tank is a a rubberized tank protector with a fake carbon fiber pattern.

jb

[rjmorel]

Is the Bags Connection made for the RX3 or does it also fit another bike? In other words which one do you need to order to fit RX3? thanks, rj

[yarimurray]

That is a clever bag set-up. Nice tank protector too. I also like the look of the bike without the trunk.