Go Back   ChinaRiders Forums > Technical/Performance > Pure Dirt
Reply
 
Thread Tools Search this Thread Display Modes
Old 01-24-2015, 12:54 PM   #31
Nydirtbike   Nydirtbike is offline
 
Join Date: Jan 2015
Posts: 36
I'm in Rockland county


 
Reply With Quote
Old 01-24-2015, 01:22 PM   #32
Weldangrind   Weldangrind is offline
 
Weldangrind's Avatar
 
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
Quote:
Originally Posted by Nydirtbike View Post
How hard is it to jet the carb ? I'm pretty mechanicle good.
It could be tough to find slow jets for that carb. A 30mm Mikuni is much easier. Here's one: http://www.ebay.com/itm/Carburetor-A...c1c85d&vxp=mtr
__________________
Weldangrind

"I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer


 
Reply With Quote
Old 01-28-2015, 10:06 PM   #33
Nydirtbike   Nydirtbike is offline
 
Join Date: Jan 2015
Posts: 36
hey weld

where can i find the replacement jets for the 30mm mikuni carb.

i ordered the carb but want to up the jets like you recommended.

110 main and should i do 30 0r 25


 
Reply With Quote
Old 01-29-2015, 06:44 PM   #34
Weldangrind   Weldangrind is offline
 
Weldangrind's Avatar
 
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
The slow jet choice depends on your specific bike and your elevation. With a stock pipe near sea level, I'd stick with a 25. With a free-flowing muffler, try a 30. Whatever your bike needs to start quickly and idle smoothly.

Another way to look at it is if the pilot mixture screw needs to be backed out more that two full turns, your slow jet is too small.

Remove the slow jet and main jet from your carb and then hit www.jetsrus.com. Compare the jets from your Mikuni to the jets in the pictures, and ensure that the measurements match. Once you've found a match, you'll learn what the numerical designation is for your jets, and which point you can shop at www.jetsrus.com or eBay.
__________________
Weldangrind

"I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer


 
Reply With Quote
Old 01-31-2015, 08:15 PM   #35
Gr8rcher   Gr8rcher is offline
 
Join Date: Jan 2015
Location: Texas
Posts: 32
Mine came with a 20 and a 100. Needle has not been touched starts with a quick bump of the starter or 1 -2 kicks, I'm leaving mine like it is for now.
__________________
If you're gonna go, go with a smile. (The Joker)


 
Reply With Quote
Old 01-31-2015, 08:48 PM   #36
Nydirtbike   Nydirtbike is offline
 
Join Date: Jan 2015
Posts: 36
hey Gr8rcher

hows the bike run now ever since the valves were adjusted and the new carb?


 
Reply With Quote
Old 01-31-2015, 09:41 PM   #37
Gr8rcher   Gr8rcher is offline
 
Join Date: Jan 2015
Location: Texas
Posts: 32
Couldn't be happier
__________________
If you're gonna go, go with a smile. (The Joker)


 
Reply With Quote
Old 02-01-2015, 12:32 PM   #38
Weldangrind   Weldangrind is offline
 
Weldangrind's Avatar
 
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
Awesome! I'm glad that worked out for you. You'll now have the ability to change jets if you make changes to the intake and exhaust.
__________________
Weldangrind

"I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer


 
Reply With Quote
Old 02-01-2015, 05:38 PM   #39
culcune   culcune is offline
 
culcune's Avatar
 
Join Date: May 2006
Location: Yuma, Arizona
Posts: 9,035
Have you ordered/installed the front sprockets?
__________________
"They say that life's a carousel, spinning fast you got to ride it well..."

TGB Delivery Scooter 150
TMEC 200 Enduro--carcass is sadly rotting in the backyard


 
Reply With Quote
Old 02-02-2015, 05:29 PM   #40
Nydirtbike   Nydirtbike is offline
 
Join Date: Jan 2015
Posts: 36
i did install a new front sprocket. i went with a 12 tooth
the original one was a 14 tooth. Big difference it bottom end


 
Reply With Quote
Old 02-02-2015, 06:56 PM   #41
Weldangrind   Weldangrind is offline
 
Weldangrind's Avatar
 
Join Date: Mar 2009
Location: Sardis, BC, Canada
Posts: 25,977
I'll bet it climbs any hill you point it at.
__________________
Weldangrind

"I figure I'm well-prepared for coping with a bike that comes from the factory with unresolved issues and that rewards the self-reliant owner." - Buccaneer


 
Reply With Quote
Old 02-02-2015, 10:05 PM   #42
Nydirtbike   Nydirtbike is offline
 
Join Date: Jan 2015
Posts: 36
i hope lol. Stillwaiting for the spring this ny weather is killing me.
I should be getting my new 30mm muniki carb in like you suggested any day now.
Cant wait to install that.


 
Reply With Quote
Old 02-05-2015, 09:09 AM   #43
Gr8rcher   Gr8rcher is offline
 
Join Date: Jan 2015
Location: Texas
Posts: 32
FedEx Smartpost Sucks it took 6 days to get my carb, from Cali to TX usually takes 2-3 for a USPS package to arrive.
__________________
If you're gonna go, go with a smile. (The Joker)


 
Reply With Quote
Old 02-05-2015, 10:44 PM   #44
Nydirtbike   Nydirtbike is offline
 
Join Date: Jan 2015
Posts: 36
yes took for ever. Got it today finally lol
Prob sat or sunday ill install it. Sucks because its going to snow sunday and monday now i can't even test it lol my luck.


 
Reply With Quote
Old 02-09-2015, 04:03 PM   #45
jimlao92   jimlao92 is offline
 
Join Date: Jan 2015
Posts: 24
hello, nice bike! how is the carb working out for you?


 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:03 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.