My Current List of Mods (Vader 125)

_MaXiPaD_ · 02-25-2017, 01:53 PM

Alright, so after receiving the same questions over-and-over regarding the mods I have done to my Vader, I decided to finally put a list together so that you guys can see what mods I have done to the bike and where you can get these mods at.

Here is my current list for the Boom Vader 125:

- Front Sprocket: 428-16t (Fit 17mm Shaft) (~$8)
Link:
http://www.ebay.com/itm/Motorcycle-A...lVEApO&vxp=mtr

- Headlight Bulbs: H6 BA20D Type 5W LED (~$9)
Link:
http://www.ebay.com/itm/2x-H6-BA20D-...oAAMXQLs5RrkpK

- Mikuni 26mm Carburetor + Intake Pipe + Pod Filter (~$38-$43)
Link:
https://www.amazon.com/GooDeal-Carbu...+Pit+Dirt+Bike

- Mikuni Jets – Includes Jet Sizes From 88 – 125 (I’m currently running a 120) (~$10)
Link:
https://www.amazon.com/Wings-Mikuni-...ds=mikuni+jets

- Fuel Petcock – This is optional, but recommended if you decide to buy the 26mm Mikuni since there is no built-in petcock in the carburetor. (~$5)
Link:
https://www.amazon.com/INLINE-VALVE-...KART+DIRT+BIKE

- UNI Breather Filter Push in Type 5/16 Inch Universal – Used on the crankcase ventilator hose (~$13)
Link:
https://www.amazon.com/Breather-Filt...Inch+Universal

- RSC Clutch Lever – Shorty (~$105)
Link:
http://www.righteousstuntmetal.com/i...al/levers.html

- Brembo Lefthand Master Cylinder/Lever w/ Built-In Reservoir.
This was included in a Grom Junction Valve kit that I ordered from TacticalMindz.com . However, DO NOT ORDER THE JUNCTION VALVE KIT. I could not get the Junction Valve to work correctly in the rear master cylinder. It kept blowing out under high pressure. If you want a Stunt Handbrake, find a Left Hand Master Cylinder on eBay.

- 65” Steel Braided Brakeline (From Lefthand Master Cylinder directly back to rear brake)
There is no longer a link for the Brake Line I ordered. I paid $15 for it, but expect to pay ~$50-70 for a line that long.

- Exhaust: AR Low Mount Exhaust (For 2014 Grom) (~$130)
**HEADS UP: This exhaust requires extra modifying to fit! I had to relocate my kickstand because of it! BUYER BEWARE!
Link:
https://www.amazon.com/Honda-Aodonly.../dp/B01BHQ7E6S

- Stunt Bar / 12 Bar
I built mine at work. If you’d like a 12 Bar, check out uptrade7784 aka “402 Innovations.” He builds Stunt Bars for the Omaha Grom Squad (including Fooligan himself). They look nice and are very well priced (Currently @ $230).
http://www.ebay.com/usr/uptrade7784?...p2047675.l2559

There is the list! I’ll continue to add to the list as I continue to modify the bike.

And if you guys were curious about my Hawk 250, the only mods I have done to it are: 16t Front Sprocket, DPR8EIX-9 Iridium IX Spark Plug, and exhaust baffle removal. I’m also using a larger main jet in the stock carb, but I can’t remember what size at the moment. The Jet Kit that I listed for the Vader 125 Mikuni Carb also works with the stock carb on the Hawk 250.

jsumd · 02-25-2017, 05:33 PM

Thanks for putting this list together, maxi! First things I'm going to do, almost right away, is change the bulbs, carb, and sprocket.

_MaXiPaD_ · 02-27-2017, 10:13 AM

Quote:

Originally Posted by jsumd

Thanks for putting this list together, maxi! First things I'm going to do, almost right away, is change the bulbs, carb, and sprocket.

No problem! Those would be great options to start with!

Crispy92 · 03-10-2017, 12:37 AM

So whats your top speed with the mods? Are the led lights for the startor issue i heard of?

Jrack · 03-31-2017, 12:45 PM

I'm still waiting for my Vader to be delivered. In the meantime I've ordered the headlight bulbs, new clutch and break levers, crossbar, pod air filter and mikuni jets. I'm going to up jet the stock carb and hope that makes a difference. I'll probably mod the exhaust as well. Thank you for the list and vids!!

ben2go · 03-31-2017, 12:52 PM

But where are the pics of this mad ass machine?

MOTOXtreme · 03-31-2017, 12:59 PM

Quote:

Originally Posted by ben2go

But where are the pics of this mad ass machine?

Youtube. He has a bunch of Vader videos

ben2go · 03-31-2017, 01:19 PM

Quote:

Originally Posted by MOTOXtreme

Youtube. He has a bunch of Vader videos

Of course, but I would like to see _MaXiPaD_'s mean machine with all of it's mods.

OregonRider · 03-31-2017, 02:06 PM

He has some better photos on his Instagram. @maxipadmoto

martim · 07-20-2017, 10:20 PM

Many comments about paint that burns off after a few uses...is this true?
Do you have another recommendation for an exhaust?
Are there exhausts that aren't annoyingly loud? Noise is fine, especially deep noice but nothing yelpy...hope that makes sense. Thanks,

martim · 07-21-2017, 02:11 PM

Between the Mikuni carburetor and the Chimera intake system, which one would you guys pick and why?

Same exercise between the Dual Exhaust produced by MNTHBX or the
https://www.mnnthbx.com/product/dual-underbody-exhaust/

Yoshumura RS-9
https://www.mnnthbx.com/product/yosh...arbon-exhaust/

Or if you have a better recommendation, let me know.

I am just looking for help since I am new to this! Thanks!

Skin Mechanic · 07-21-2017, 02:27 PM

Quote:

Originally Posted by _MaXiPaD_

- Exhaust: AR Low Mount Exhaust (For 2014 Grom) (~$130)
**HEADS UP: This exhaust requires extra modifying to fit! I had to relocate my kickstand because of it! BUYER BEWARE!
Link:
https://www.amazon.com/Honda-Aodonly.../dp/B01BHQ7E6S

I bought this exhaust for my bike and gave it away after 2 rides. It was obnoxiously loud and cost me about 4mph on the top end. My bike sounds and performs much better with the modded factory exhaust, YMMV of course.

martim · 07-21-2017, 04:07 PM

What about between these 2 exhausts...

Same exercise between the Dual Exhaust produced by MNTHBX or the
https://www.mnnthbx.com/product/dual-underbody-exhaust/

Yoshumura RS-9
https://www.mnnthbx.com/product/yosh...arbon-exhaust/

?

Skin Mechanic · 07-22-2017, 02:19 PM

Quote:

Originally Posted by martim

What about between these 2 exhausts...

Same exercise between the Dual Exhaust produced by MNTHBX or the
https://www.mnnthbx.com/product/dual-underbody-exhaust/

Yoshumura RS-9
https://www.mnnthbx.com/product/yosh...arbon-exhaust/

?

Dual exhaust on a single cylinder engine makes as much sense as sticking 2 carbs on the intake. Given the marginal performance gain, I can't justify spending more for an exhaust system than what a replacement engine costs.

martim · 07-25-2017, 06:05 PM

Makes an insane amount of noise anyways. I am leaning towards the Yoshi RS-2 or RS-9. Do you think I'll have an issue installing either on a Vader or a Venom?

Have you heard of someone replacing the back sprocket on these to a 30?

02-25-2017, 01:53 PM	#1
_MaXiPaD_ Join Date: May 2016 Posts: 59	My Current List of Mods (Vader 125) Alright, so after receiving the same questions over-and-over regarding the mods I have done to my Vader, I decided to finally put a list together so that you guys can see what mods I have done to the bike and where you can get these mods at. Here is my current list for the Boom Vader 125: - Front Sprocket: 428-16t (Fit 17mm Shaft) (~$8) Link: http://www.ebay.com/itm/Motorcycle-A...lVEApO&vxp=mtr - Headlight Bulbs: H6 BA20D Type 5W LED (~$9) Link: http://www.ebay.com/itm/2x-H6-BA20D-...oAAMXQLs5RrkpK - Mikuni 26mm Carburetor + Intake Pipe + Pod Filter (~$38-$43) Link: https://www.amazon.com/GooDeal-Carbu...+Pit+Dirt+Bike - Mikuni Jets – Includes Jet Sizes From 88 – 125 (I’m currently running a 120) (~$10) Link: https://www.amazon.com/Wings-Mikuni-...ds=mikuni+jets - Fuel Petcock – This is optional, but recommended if you decide to buy the 26mm Mikuni since there is no built-in petcock in the carburetor. (~$5) Link: https://www.amazon.com/INLINE-VALVE-...KART+DIRT+BIKE - UNI Breather Filter Push in Type 5/16 Inch Universal – Used on the crankcase ventilator hose (~$13) Link: https://www.amazon.com/Breather-Filt...Inch+Universal - RSC Clutch Lever – Shorty (~$105) Link: http://www.righteousstuntmetal.com/i...al/levers.html - Brembo Lefthand Master Cylinder/Lever w/ Built-In Reservoir. This was included in a Grom Junction Valve kit that I ordered from TacticalMindz.com . However, DO NOT ORDER THE JUNCTION VALVE KIT. I could not get the Junction Valve to work correctly in the rear master cylinder. It kept blowing out under high pressure. If you want a Stunt Handbrake, find a Left Hand Master Cylinder on eBay. - 65” Steel Braided Brakeline (From Lefthand Master Cylinder directly back to rear brake) There is no longer a link for the Brake Line I ordered. I paid $15 for it, but expect to pay ~$50-70 for a line that long. - Exhaust: AR Low Mount Exhaust (For 2014 Grom) (~$130) HEADS UP: This exhaust requires extra modifying to fit! I had to relocate my kickstand because of it! BUYER BEWARE! Link: https://www.amazon.com/Honda-Aodonly.../dp/B01BHQ7E6S - Stunt Bar / 12 Bar I built mine at work. If you’d like a 12 Bar, check out uptrade7784 aka “402 Innovations.” He builds Stunt Bars for the Omaha Grom Squad (including Fooligan himself). They look nice and are very well priced (Currently @ $230). http://www.ebay.com/usr/uptrade7784?...p2047675.l2559 There is the list! I’ll continue to add to the list as I continue to modify the bike. And if you guys were curious about my Hawk 250, the only mods I have done to it are: 16t Front Sprocket, DPR8EIX-9 Iridium IX Spark Plug, and exhaust baffle removal. I’m also using a larger main jet in the stock carb, but I can’t remember what size at the moment. The Jet Kit that I listed for the Vader 125 Mikuni Carb also works with the stock carb on the Hawk 250. __________________ MAXIPADmoto YouTube: MAXIPADmoto Instagram: maxipadmoto Twitter: MAXIPADmoto** Bikes I own: RPS Hawk 250, Boom 125cc Vader, KTM 625 SMC & Yamaha V-Max (Gen 1)
	4

07-20-2017, 10:20 PM	#10
martim Join Date: Jul 2017 Posts: 28	Exhaust Many comments about paint that burns off after a few uses...is this true? Do you have another recommendation for an exhaust? Are there exhausts that aren't annoyingly loud? Noise is fine, especially deep noice but nothing yelpy...hope that makes sense. Thanks,
	0

02-25-2017, 05:33 PM	#2
jsumd Join Date: Feb 2017 Posts: 386	Thanks for putting this list together, maxi! First things I'm going to do, almost right away, is change the bulbs, carb, and sprocket.
	0

03-10-2017, 12:37 AM	#4
Crispy92 Join Date: Mar 2017 Posts: 1	So whats your top speed with the mods? Are the led lights for the startor issue i heard of?
	0

03-31-2017, 12:45 PM	#5
Jrack Join Date: Mar 2017 Location: Northern Wisconsin Posts: 64	I'm still waiting for my Vader to be delivered. In the meantime I've ordered the headlight bulbs, new clutch and break levers, crossbar, pod air filter and mikuni jets. I'm going to up jet the stock carb and hope that makes a difference. I'll probably mod the exhaust as well. Thank you for the list and vids!!
	0

03-31-2017, 12:52 PM	#6
ben2go Join Date: Jun 2011 Posts: 1,335	But where are the pics of this mad ass machine?
	0

03-31-2017, 02:06 PM	#9
OregonRider Join Date: Mar 2017 Posts: 25	He has some better photos on his Instagram. @maxipadmoto
	1

07-21-2017, 02:11 PM	#11
martim Join Date: Jul 2017 Posts: 28	Between the Mikuni carburetor and the Chimera intake system, which one would you guys pick and why? Same exercise between the Dual Exhaust produced by MNTHBX or the https://www.mnnthbx.com/product/dual-underbody-exhaust/ Yoshumura RS-9 https://www.mnnthbx.com/product/yosh...arbon-exhaust/ Or if you have a better recommendation, let me know. I am just looking for help since I am new to this! Thanks!
	0

07-21-2017, 04:07 PM	#13
martim Join Date: Jul 2017 Posts: 28	What about between these 2 exhausts... Same exercise between the Dual Exhaust produced by MNTHBX or the https://www.mnnthbx.com/product/dual-underbody-exhaust/ Yoshumura RS-9 https://www.mnnthbx.com/product/yosh...arbon-exhaust/ ?
	0

07-25-2017, 06:05 PM	#15
martim Join Date: Jul 2017 Posts: 28	Makes an insane amount of noise anyways. I am leaning towards the Yoshi RS-2 or RS-9. Do you think I'll have an issue installing either on a Vader or a Venom? Have you heard of someone replacing the back sprocket on these to a 30?
	0