Left engine cover crank bolt access screw

weiser23 · 10-27-2021, 08:06 PM

After smelling oil at every stop i looked down and noticed the left side crank bolt access bolt
Is gone, I know I have checked it recently but it must have vibrated a off , wasn’t sure what was going to happen I’d had a 40 Mile ride home but made it ( but the question is where can I get one in a hurry what is the proper name for this and the is there a Chinese MacGyver solution to what I could use till I can get a new one

TominMO · 10-27-2021, 08:53 PM

Quote:

Originally Posted by weiser23

.....is there a Chinese MacGyver solution to what I could use till I can get a new one

Gorilla tape. After you get the bolt access cover and remove the tape, use WD-40 to remove any glue left on the case.

weiser23 · 10-28-2021, 06:45 PM

Stator Cover Crank Case Plug Cap Is what I need don’t know if any Honda models should work which I found some on line, I will try the tape until I can find the part I tried a few Chinese motorcycle dealer and get no response

**JerryHawk250** · 10-28-2021, 07:12 PM

What bike is this on?

weiser23 · 10-28-2021, 07:17 PM

Wow I can’t believe I didn’t put that in 2020 hawk 250

dirtbkr188 · 10-28-2021, 07:57 PM

What is the ID of the hole where the plug cap goes?

**JerryHawk250** · 10-28-2021, 08:04 PM

Check with TXpowersports or Orionpowersports as they both carry and sell parts for the Hawk.

weiser23 · 10-28-2021, 08:57 PM

If your sitting on bike it’s the left side where you turn the engine over to set top dead center
Txpowersports is one that never responded, I saw some Honda cap on eBay, but wasn’t sure if they would work

dirtbkr188 · 10-28-2021, 09:35 PM

I was looking for the inner diameter of of the hole, in mm, I stumbled across one earlier today with an outer diameter of 28.3mm, measured at the threads. I know the overall diameter is slightly bigger, and may be match to a Honda one shown HERE. Part #15 is 30mm wide overall, and part #19 (o-ring) is 27mm

**JerryHawk250** · 10-29-2021, 08:19 AM

Quote:

Originally Posted by dirtbkr188

I was looking for the inner diameter of of the hole, in mm, I stumbled across one earlier today with an outer diameter of 28.3mm, measured at the threads. I know the overall diameter is slightly bigger, and may be match to a Honda one shown HERE. Part #15 is 30mm wide overall, and part #19 (o-ring) is 27mm

I'm pretty sure these are the correct parts because that's the same as what's on my Ghost which is a clone of the CRF230F engine.

weiser23 · 10-29-2021, 09:19 AM

Unfortunately it has it’s unavailable

dirtbkr188 · 10-29-2021, 09:58 AM

Possibly this one will work for you? Might be worth a try...

weiser23 · 10-29-2021, 06:27 PM

Quote:

Originally Posted by dirtbkr188

Possibly this one will work for you? Might be worth a try...

Thanks I ordered one I hope it works I have I gorilla taped for now seems to be working

weiser23 · 11-01-2021, 09:12 PM

Thanks the part work

10-28-2021, 07:12 PM	#4
JerryHawk250 Moderator Join Date: Oct 2016 Location: Houma, La. Posts: 11,553	What bike is this on? __________________ 2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel
	0

10-28-2021, 08:04 PM	#7
JerryHawk250 Moderator Join Date: Oct 2016 Location: Houma, La. Posts: 11,553	Check with TXpowersports or Orionpowersports as they both carry and sell parts for the Hawk. __________________ 2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel
	0

10-27-2021, 08:06 PM	#1
weiser23 Join Date: Jan 2011 Location: mechanicsburg pa Posts: 166	Left engine cover crank bolt access screw After smelling oil at every stop i looked down and noticed the left side crank bolt access bolt Is gone, I know I have checked it recently but it must have vibrated a off , wasn’t sure what was going to happen I’d had a 40 Mile ride home but made it ( but the question is where can I get one in a hurry what is the proper name for this and the is there a Chinese MacGyver solution to what I could use till I can get a new one
	0

10-28-2021, 06:45 PM	#3
weiser23 Join Date: Jan 2011 Location: mechanicsburg pa Posts: 166	Stator Cover Crank Case Plug Cap Is what I need don’t know if any Honda models should work which I found some on line, I will try the tape until I can find the part I tried a few Chinese motorcycle dealer and get no response
	0

10-28-2021, 07:17 PM	#5
weiser23 Join Date: Jan 2011 Location: mechanicsburg pa Posts: 166	Wow I can’t believe I didn’t put that in 2020 hawk 250
	0

10-28-2021, 07:57 PM	#6
dirtbkr188 Join Date: Aug 2009 Posts: 500	What is the ID of the hole where the plug cap goes?
	0

10-28-2021, 08:57 PM	#8
weiser23 Join Date: Jan 2011 Location: mechanicsburg pa Posts: 166	If your sitting on bike it’s the left side where you turn the engine over to set top dead center Txpowersports is one that never responded, I saw some Honda cap on eBay, but wasn’t sure if they would work
	0

10-28-2021, 09:35 PM	#9
dirtbkr188 Join Date: Aug 2009 Posts: 500	I was looking for the inner diameter of of the hole, in mm, I stumbled across one earlier today with an outer diameter of 28.3mm, measured at the threads. I know the overall diameter is slightly bigger, and may be match to a Honda one shown HERE. Part #15 is 30mm wide overall, and part #19 (o-ring) is 27mm
	1

10-29-2021, 09:19 AM	#11
weiser23 Join Date: Jan 2011 Location: mechanicsburg pa Posts: 166	Unfortunately it has it’s unavailable
	0

10-29-2021, 09:58 AM	#12
dirtbkr188 Join Date: Aug 2009 Posts: 500	Possibly this one will work for you? Might be worth a try...
	2

11-01-2021, 09:12 PM	#14
weiser23 Join Date: Jan 2011 Location: mechanicsburg pa Posts: 166	Thanks the part work
	2