Im back. Little quad

Bruce's · 04-15-2018, 01:02 PM

No shifter in the engine number picture above ,full auto .

FLASHLIGHTBOY · 04-15-2018, 05:21 PM

the stamp on the black part of the motor does not lie... it is casted into the head part... it is not a semi as there is no place for the shifter.... this atv is popular make.. the real question is the front suspension or the rear swingarm,... if you are lucky it is not a GIO,,,, POOR SWINGARM BUSHINGS AND FRONT SUSPENSION SETUP.. the bearings for the rear axle are easy to pick up... check ebay if you can wait from CHINA cheap.. or locally about 3-5 times as much..

Angus67 · 12-10-2018, 12:05 AM

Stumbled on this old thread i started,.
Poor little guy sat outside all summer, and got blasted by sun, pelted by rain. Dragged the little quad in and put in new starter, new carb. Pretty much fired right up.
Im trying to hook up a relay for the starter.
Should there be 12v on the yellow/red wire fron starter button?
Can i just use a momenttary high amp button that is wired to the starter from the batter,and just bypass the original start button?
The kill swich works. Started button shows continuity. Were does the opower for the starter button come from?
It is charging. All systems are goog.

pete · 12-10-2018, 04:13 AM

Quote:

Originally Posted by Angus67

Started button shows continuity. Were does the opower for the starter button come from?

AC current from the recifier... DC current will burn the start button out in seconds..
the starter relay dose require quit a bit of current to oparate the magnetic switch..

there should be a diode somewhere near the starter relay to stop the AC & DC current
coming in contact with each other...

A high amp button powered straight from the battrey will work..

..

04-15-2018, 05:21 PM	#2
FLASHLIGHTBOY Join Date: May 2009 Location: SASKATOON Posts: 1,161	Size the stamp on the black part of the motor does not lie... it is casted into the head part... it is not a semi as there is no place for the shifter.... this atv is popular make.. the real question is the front suspension or the rear swingarm,... if you are lucky it is not a GIO,,,, POOR SWINGARM BUSHINGS AND FRONT SUSPENSION SETUP.. the bearings for the rear axle are easy to pick up... check ebay if you can wait from CHINA cheap.. or locally about 3-5 times as much.. __________________ DEALER FOR ZSTAR & GIO PRODUCTS, TAOTAO ABIBABA ATV ETC
	0

12-10-2018, 12:05 AM	#3
Angus67 Join Date: Oct 2017 Location: shelton, Washington Posts: 167	Stumbled on this old thread i started,. Poor little guy sat outside all summer, and got blasted by sun, pelted by rain. Dragged the little quad in and put in new starter, new carb. Pretty much fired right up. Im trying to hook up a relay for the starter. Should there be 12v on the yellow/red wire fron starter button? Can i just use a momenttary high amp button that is wired to the starter from the batter,and just bypass the original start button? The kill swich works. Started button shows continuity. Were does the opower for the starter button come from? It is charging. All systems are goog. __________________ 2006 roketa 200cc 1971 Yamaha xs650 2x 1980 xs650, 1 is a café, other is a chopper/brat 1972 Honda xl250 2x early 90's Honda rf600 parts bikes more mc junk laying around.
	0

04-15-2018, 01:02 PM	#1
Bruce's Join Date: Apr 2015 Location: Sudbury ,Ontario Posts: 855	No shifter in the engine number picture above ,full auto .
	1