2020 Bashan brozz 250 chain replacement question

Brozz250 · 11-13-2020, 11:43 AM

Are you supposed to adjust the chain with the bike up on a stand or on the ground. The operation manual says on a stand but it shows an image of a drum set up

JerseyTBR7 · 11-13-2020, 12:40 PM

I have done it both on the stand and ground. You just have to roll the bike back and forth on the ground to verify slack and tightness on all the links. Its a tad more convenient on a stand since you have the wheel rolling free. On other bikes with a built-in center stand, its a piece of cake.

**JerryHawk250** · 11-13-2020, 12:45 PM

Chain slack should be check while sitting on the bike or have someone else sit on it. Not sure on the Brozz but on my Hawk the chain will get tighter with a load. After you have done it the first time you can check how much slack you have without a load on the bike so you will know how much to leave the next time.

ChillRider · 11-14-2020, 04:45 AM

Your chain will be the tightest with the swingarm at the mid of its travel (or with both sprockets completely aligned with the swingarm). Both the fully loaded and fully unloaded positions will be looser, that's why you need to verify with the bike loaded.

The per-manual specified slack is almost always stated for an unloaded bike, the idea being that with a typical marching order weight the chain will be near its maximum tension, and it can only go looser from there.

Of course, even when loaded, you don't want it to be completely rigid, or, worse, cross its maximum tension point before you even put your entire weight on it.

11-13-2020, 11:43 AM	#1
Brozz250 Join Date: Nov 2020 Posts: 19	2020 Bashan brozz 250 chain replacement question Are you supposed to adjust the chain with the bike up on a stand or on the ground. The operation manual says on a stand but it shows an image of a drum set up
	0

11-13-2020, 12:45 PM	#3
JerryHawk250 Moderator Join Date: Oct 2016 Location: Houma, La. Posts: 11,574	Chain slack should be check while sitting on the bike or have someone else sit on it. Not sure on the Brozz but on my Hawk the chain will get tighter with a load. After you have done it the first time you can check how much slack you have without a load on the bike so you will know how much to leave the next time. __________________ 2023 Lifan Lycan 250 Chopper 2023 Venom Evader 2022 Lifan KPX250 2020 Kawasaki Vulcan S 2004 Honda ST 1300 2016 Black Hawk 250 (sold) Keihin PE30 carb,125 main,38 slow.Pod filter,ported & decked head 10:1 CR,Direct Ignition Coil,15/40Sprockets,NGK DPR8EIX-9,De-Cat,Dual Oil Cooler,Digital Cluster 2016 Cazador180 XL 2014 Coolster150 JerryHawk250.com My YouTube Channel
	0

11-13-2020, 12:40 PM	#2
JerseyTBR7 Join Date: Oct 2020 Posts: 130	I have done it both on the stand and ground. You just have to roll the bike back and forth on the ground to verify slack and tightness on all the links. Its a tad more convenient on a stand since you have the wheel rolling free. On other bikes with a built-in center stand, its a piece of cake.
	0

11-14-2020, 04:45 AM	#4
ChillRider Join Date: Jun 2020 Location: A small country with a funny name Posts: 164	Your chain will be the tightest with the swingarm at the mid of its travel (or with both sprockets completely aligned with the swingarm). Both the fully loaded and fully unloaded positions will be looser, that's why you need to verify with the bike loaded. The per-manual specified slack is almost always stated for an unloaded bike, the idea being that with a typical marching order weight the chain will be near its maximum tension, and it can only go looser from there. Of course, even when loaded, you don't want it to be completely rigid, or, worse, cross its maximum tension point before you even put your entire weight on it.
	0