Go Back   ChinaRiders Forums > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search
Page 1 of 2 1 2
Showing results 1 to 25 of 48
Search took 0.01 seconds. Search: Posts Made By: Lkhangee
Forum: ATVs 05-24-2020, 01:00 PM
Replies: 4
Views: 762
Posted By Lkhangee
The green cable is not coming from the stator....

The green cable is not coming from the stator. It's exiting from the rectifier. I am a bit confused about it.

And why could it have blasted when no battery was connected to rectified?
Forum: ATVs 05-24-2020, 12:58 PM
Replies: 4
Views: 762
Posted By Lkhangee
But battery negative is already grounded to...

But battery negative is already grounded to chassis.

And from rectifier 5 cables coming out two are from the pulsar coil. And three yellow cables from the stator.. The pulsar green is not...
Forum: ATVs 05-24-2020, 07:17 AM
Replies: 4
Views: 762
Posted By Lkhangee
Here are images of the rectifier connector

Here are images of the rectifier connector
Forum: ATVs 05-24-2020, 07:14 AM
Replies: 4
Views: 762
Posted By Lkhangee
Help needed to wire 3 phase rectifier to stator

I have swapped engine in my bike and new engine is dc cdi and it's stator has 12 poles coils.
It has 3 wires coming from its stator yellow color and two wires from the pulsar coil. The yellow wires...
Forum: Street 05-20-2018, 05:08 PM
Replies: 3
Views: 655
Posted By Lkhangee
It seems that the Water level was decreased...

It seems that the Water level was decreased initially because the water system needed to prime itself once all water galleries and channels were full no bubbles or water reduction was observed.
...
Forum: Street 05-20-2018, 09:44 AM
Replies: 3
Views: 655
Posted By Lkhangee
Is this gushing going on in my radiator normal? Or an indicator of blown head gasket?

UvHi
I have 163ML class engine. Just finished its top end work. Replaced cylinder, piston, head gasket, valve guides, valves, valve seals, lapped new valves.

Now I m checking at the radiator cap...
Forum: Street 05-15-2018, 01:16 PM
Replies: 4
Views: 622
Posted By Lkhangee
Any input as I what you guys are using? I have...

Any input as I what you guys are using?
I have set mine to 0.004" per inch for top and. 0045 per inch for second.
Forum: Street 05-08-2018, 02:32 PM
Replies: 4
Views: 622
Posted By Lkhangee
I m hesitant in expanding the gap. Not a norm in...

I m hesitant in expanding the gap. Not a norm in this part of the world. Any buddy who has done top end work on these Chinese water cooled engines? What is the gap as per Chinese as this is not...
Forum: Street 05-06-2018, 01:22 PM
Replies: 4
Views: 622
Posted By Lkhangee
Using bore x. 0040"= 0.2514 mm for top ring And...

Using bore x. 0040"= 0.2514 mm for top ring
And 0.0045" second ring glass comes out yo be 0.281mm
What about oil scrapper and the two oil rings? Should they be set to minimum 0.015"= 0.381mm?

...
Forum: Street 05-06-2018, 10:16 AM
Replies: 6
Views: 749
Posted By Lkhangee
The needle might be bent. Or might be stucking...

The needle might be bent. Or might be stucking int the emulsion tube which usually happens when the needle jet is improperly seated. (the jet through which the needle goes in /out)
Forum: Street 05-06-2018, 09:43 AM
Replies: 4
Views: 622
Posted By Lkhangee
Ring end gap for Chinese water cooled cg clones

Hi
What's the ideal rings end gap for Chinese water cooled cg replica? 163ML class engine?

The bore is 63mm and stroke is 62.2mm

I bought new cylinder and piston kit and ring end gap at any...
Forum: ATVs 05-04-2018, 01:25 PM
Replies: 4
Views: 936
Posted By Lkhangee
Pz27 in 250cc? What are jets and needles specs?

Pz27 in 250cc?
What are jets and needles specs?
Forum: Street 05-04-2018, 05:45 AM
Replies: 11
Views: 1,098
Posted By Lkhangee
For 163ML class engines what are the specs of...

For 163ML class engines what are the specs of valves? The replacement valves that arrived are 2mm shorter and the valve stem place is also 1-2mm shorter.
Forum: Street 05-04-2018, 05:44 AM
Replies: 11
Views: 1,098
Posted By Lkhangee
Here is how the head cylinder and plug looks...

Here is how the head cylinder and plug looks like.

Bought replacement cylinder and piston, replaced valves and valves guides, and lapped valves. Will tie it together to see how it turns out
Forum: Street 05-01-2018, 04:28 AM
Replies: 1
Views: 476
Posted By Lkhangee
Radiator choice for cg200 water cooled

Hi
I have 163ML 200cc water cooled engine swapped in commuter bike that originally came with air cooled cg125 type engine.

Since I bought it on scrap with no proper accessories, I m trying to...
Forum: Street 04-27-2018, 03:18 AM
Replies: 11
Views: 1,098
Posted By Lkhangee
Yes I will pull the head and see how is it.

Yes I will pull the head and see how is it.
Forum: Street 04-24-2018, 02:08 PM
Replies: 11
Views: 1,098
Posted By Lkhangee
Valves clearance is set to 0.08mm cold engine...

Valves clearance is set to 0.08mm cold engine after one day rest.
As cold as anything in its surroundings.

After full throttle at idle for hardly 2-5 seconds bike shuts off and when I Chek only...
Forum: Street 04-21-2018, 02:50 PM
Replies: 11
Views: 1,098
Posted By Lkhangee
Yes to both questions.

Yes to both questions.
Forum: Street 04-21-2018, 01:20 PM
Replies: 11
Views: 1,098
Posted By Lkhangee
Exhaust tappet gets tightened when engine reved at idle

Hi
I am using 163ML liquid cooled 200cc engine in my street bike.
While I don't Rev bike at idle. But people Rev it out of curiosity when the see liquid cooled engine in this frame.

I noticed...
Forum: Street 04-17-2018, 03:20 PM
Replies: 2
Views: 800
Posted By Lkhangee
Set both to 0.08mm as stated in most cg literature

Set both to 0.08mm as stated in most cg literature
Forum: Street 04-17-2018, 09:28 AM
Replies: 8
Views: 901
Posted By Lkhangee
Is there any upgrades kit to make it 175cc or...

Is there any upgrades kit to make it 175cc or probably 200cc?
Forum: Street 04-17-2018, 09:24 AM
Replies: 3
Views: 5,569
Posted By Lkhangee
Immense thanks for the detailed reply. ...

Immense thanks for the detailed reply.
Currently my engine 163ML liquid cooled is using ac cdi system from a 125cc cg replica bike.

Is it advisable to convert to DC cdi system.

Also what is...
Forum: Street 04-17-2018, 01:47 AM
Replies: 3
Views: 5,569
Posted By Lkhangee
Cdi vs TCI

Hi,

What's the difference and advantages of one over the other.
Some folks told me earlier Chinese tuk Tuk Tuk Rickshaws used tci bit since the mechanics that would take care of tuk Tuk in this...
Forum: Street 04-16-2018, 04:20 PM
Replies: 2
Views: 800
Posted By Lkhangee
Valve clearance for cg200 163ML water cooled engine

Hi
What is the correct valve clearance for a 200cc water cooled 163ML class engine?

I have currently set both to 0.08mm.
Regards
Forum: Street 04-15-2018, 12:20 AM
Replies: 8
Views: 901
Posted By Lkhangee
Thanks for the reference thread. Mine is Ohc not...

Thanks for the reference thread. Mine is Ohc not ohv. But I do have a water cooled 163fml and a bunch of cg 125s will try the above on that.

For current engine it already have two nozzles under...
Showing results 1 to 25 of 48
Page 1 of 2 1 2

 
Forum Jump

All times are GMT -4. The time now is 06:13 AM.

Contact Us - ChinaRiders.net - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.