ChinaRiders Forums - Search Results

		ChinaRiders Forums > Search Forums
Search Results

Showing results 1 to 10 of 10
Search took 0.00 seconds. Search: Posts Made By: JimL

Forum: Street

11-18-2014, 10:36 AM

Replies: 12

Fitting Mikuni TM28 flat slide carb on 250 V-Twin

Views: 2,870

Posted By JimL

Thanks for the help.....

:thanks:

Forum: Street

11-17-2014, 11:41 PM

Replies: 12

Fitting Mikuni TM28 flat slide carb on 250 V-Twin

Views: 2,870

Posted By JimL

More notes about this carb swap.

Part of the idle down problem is possibly due to component quality of these low-cost aftermarket Mikunis. The flat slide can be draggy at high engine vacuum on decel. That could be the reason the...

Forum: Street

11-17-2014, 11:27 PM

Replies: 4

Diamo 250 V-Twin Street Tracker

Views: 1,575

Posted By JimL

Useful tips, learned from this build.

First, I apologize about upside down pics. That is some kind of weird iPad problem. Even after I flipped them on the PC, I see they get inverted.

Some things I learned about these Virago clones:...

Forum: Street

11-13-2014, 08:40 PM

Replies: 12

Fitting Mikuni TM28 flat slide carb on 250 V-Twin

Views: 2,870

Posted By JimL

I was able to post a very short video on my home...

I was able to post a very short video on my home website. It is at the bottom of the 4th page. I am out of space allowance on that site.

The 4th page is mostly about my Bonneville stuff, but it is...

Forum: Street

11-11-2014, 07:36 PM

Replies: 12

Fitting Mikuni TM28 flat slide carb on 250 V-Twin

Views: 2,870

Posted By JimL

The finished bike is under Diamo 250 V-Twin...

The finished bike is under Diamo 250 V-Twin Street Tracker, below this thread. When it stops raining I will roll it outside for better pics. This is Oregon.....that could be a while, this time of...

Forum: Street

11-11-2014, 01:12 AM

Replies: 12

Fitting Mikuni TM28 flat slide carb on 250 V-Twin

Views: 2,870

Posted By JimL

This was so easy, I was amazed. Who would have...

This was so easy, I was amazed. Who would have thought there is aluminum inside the rubber of the manifold runners?

.....and that 1" tubing would fit into the holes (I hand filed a little taper...

Forum: Street

11-11-2014, 01:05 AM

Replies: 4

Diamo 250 V-Twin Street Tracker

Views: 1,575

Posted By JimL

Motor mounts are stock...

I cut just above the rear upper mounts. You can see them in some pics in the "TM28 carb..." post. Look at the rear exhaust pipe pic and you will see where I cut off the frame tubes. The joiner bar...

Forum: Street

11-10-2014, 11:42 PM

Replies: 12

Fitting Mikuni TM28 flat slide carb on 250 V-Twin

Views: 2,870

Posted By JimL

additional pic of Street Tracker exhaust

Rear exhaust arrangement.

Forum: Street

11-10-2014, 11:39 PM

Replies: 12

Fitting Mikuni TM28 flat slide carb on 250 V-Twin

Views: 2,870

Posted By JimL

Fitting Mikuni TM28 flat slide carb on 250 V-Twin

In the process of building my Street Tracker, I really wanted the look of a classic V-Twin and a little more power. These pics show the simple manifold that worked out well.

The manifold is a...

Forum: Street

11-10-2014, 11:04 PM

Replies: 4

Diamo 250 V-Twin Street Tracker

Views: 1,575

Posted By JimL

Diamo 250 V-Twin Street Tracker

New to the forum, I will try to post some pics of this project. I will make a separate post to show more about the manifold and exhaust, and carb setup info.

Right and left side views, plus a...

Showing results 1 to 10 of 10

Forum Jump

All times are GMT -4. The time now is 11:10 AM.