Go Back   ChinaRiders Forums > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search
Showing results 1 to 18 of 18
Search took 0.01 seconds. Search: Posts Made By: Riderx
Forum: Dual Sport/Enduro 02-27-2017, 12:04 PM
Replies: 7
Views: 3,543
Posted By Riderx
New Hawk 250 rear axle and nut stripped from factory.

After 109 miles I needed to ajust chain. Loosening the rear axle nut was difficult and upon tightening would not tighten. Initial response from dealer is to sell me a replacement axle and nut for $35...
Forum: Video and Pics 02-07-2017, 11:08 PM
Replies: 1
Views: 1,098
Posted By Riderx
2016 Texas Hawk

Simple upgrades including fine tuning intake/exhaust and sprockets. I chose to go without tank moldings and removed side cover decals.

"Any crash you walk away from is good landing".
Forum: New Member Introductions 02-04-2017, 10:54 AM
Replies: 21
Views: 2,365
Posted By Riderx
"Any crash you walk away from is a good...

"Any crash you walk away from is a good landing".
Forum: Dual Sport/Enduro 02-04-2017, 10:51 AM
Replies: 63
Views: 13,471
Posted By Riderx
"Any crash you walk away from is a good...

"Any crash you walk away from is a good landing".
Forum: Dual Sport/Enduro 02-04-2017, 10:46 AM
Replies: 63
Views: 13,471
Posted By Riderx
Hawk

You're top end speed will stiil be governed by the transmission. After tuning the engine with carb jetting, high flow intake and exhaust, the only cheap and practical transmission remedy for top end...
Forum: New Member Introductions 02-02-2017, 07:57 PM
Replies: 21
Views: 2,365
Posted By Riderx
The glass pack makes it sound like a little...

The glass pack makes it sound like a little muscle car. Can't beat the cost at $25.
Forum: Dual Sport/Enduro 02-01-2017, 04:16 PM
Replies: 9
Views: 3,059
Posted By Riderx
.... .. ........ ...........

....
..
........
...........
Forum: Dual Sport/Enduro 01-31-2017, 02:26 PM
Replies: 63
Views: 13,471
Posted By Riderx
Start with big bore kit if you can find one.

Start with big bore kit if you can find one.
Forum: New Member Introductions 01-30-2017, 07:44 PM
Replies: 21
Views: 2,365
Posted By Riderx
To prevent debri from rear wheel I fabricated...

To prevent debri from rear wheel I fabricated sheet metal guard. See pic:
I purchased the flux core wire feed welder. Works well for the price and my welding inexperience.
Forum: New Member Introductions 01-30-2017, 12:01 PM
Replies: 21
Views: 2,365
Posted By Riderx
Uni brand air filter 42mm and crankcase vent 1/2"...

Uni brand air filter 42mm and crankcase vent 1/2" pipe fitting. I removed stock airbox, cat and and stock muffler and slipped on a 23" glasspack.
Forum: New Member Introductions 01-29-2017, 07:59 PM
Replies: 21
Views: 2,365
Posted By Riderx
Catgut complete and removed the exhaust clamp. I...

Catgut complete and removed the exhaust clamp. I bought a $100, 90 amp welder from harbor freight and did the welds myself. The welds are'nt pretty but fuctional with no leaks.
Forum: New Member Introductions 01-29-2017, 07:53 PM
Replies: 7
Views: 1,126
Posted By Riderx
Hawk pics.

Hawk pics.
Forum: New Member Introductions 01-27-2017, 09:06 AM
Replies: 21
Views: 2,365
Posted By Riderx
Good idea for muffler shop. Thanks

Good idea for muffler shop. Thanks
Forum: New Member Introductions 01-26-2017, 10:10 PM
Replies: 21
Views: 2,365
Posted By Riderx
Thankyou. I have a new project to remove it....

Thankyou. I have a new project to remove it. Probably cut it out with sawsall or cutoff wheel and jb weld pipe back togethether.
Forum: New Member Introductions 01-26-2017, 09:23 PM
Replies: 21
Views: 2,365
Posted By Riderx
Good question. Where is the cat located?

Good question. Where is the cat located?
Forum: New Member Introductions 01-26-2017, 09:03 PM
Replies: 21
Views: 2,365
Posted By Riderx
New Hawk owner in Pearland, Texas. Glasspack exhaust etc...

A fun new toy with upgrades that don't break the bank. Top speed 66mph.
Forum: New Member Introductions 01-26-2017, 08:03 PM
Replies: 7
Views: 1,126
Posted By Riderx
Thanks. She runs good. I can stab the throttle at...

Thanks. She runs good. I can stab the throttle at idle without stall and no popping at high speed. Very responsive with modified stock carb. 110 mikuni jet,two spacers on the needle, and one full...
Forum: New Member Introductions 01-26-2017, 06:15 PM
Replies: 7
Views: 1,126
Posted By Riderx
New Hawk owner in Houston, TX

I got my new hawk 250 last month and enjoy tinkering on it and riding the trails.
I've made a couple of modifications including high flow intake, exhaust (sounds great), rejetted, shimmed needle jet...
Showing results 1 to 18 of 18

 
Forum Jump

All times are GMT -4. The time now is 09:46 PM.

Contact Us - ChinaRiders.net - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.