Go Back   ChinaRiders Forums > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search
Page 1 of 3 1 23
Showing results 1 to 25 of 54
Search took 0.01 seconds. Search: Posts Made By: Lukas
Forum: Zongshen RX3 10-19-2021, 08:38 PM
Replies: 108
Views: 11,506
Posted By Lukas
I think a longer shock with a longer spring would...

I think a longer shock with a longer spring would be better than the stock one, but if it turns out the spring is the same length but the shock is longer then I'll buy a $60 dollar shock with a 7mm...
Forum: Zongshen RX3 10-19-2021, 05:40 PM
Replies: 108
Views: 11,506
Posted By Lukas
Thanks a lot I was worried about the swingarm,...

Thanks a lot I was worried about the swingarm, now I know that the bike will not turn over by the way I contacted the Chinese guy about the rear shock absorber I want to replace it with a longer one,...
Forum: Zongshen RX3 10-19-2021, 03:39 PM
Replies: 108
Views: 11,506
Posted By Lukas
You might want to try with your broken ecu first...

You might want to try with your broken ecu first to be safe, as it only has a slow RPM problem, as far as the side foot is concerned, if it can't be done programmatically, then you would have to...
Forum: Zongshen RX3 09-23-2021, 10:19 AM
Replies: 108
Views: 11,506
Posted By Lukas
You have all the hardware, you can download the...

You have all the hardware, you can download the map and send it to oldschool tuning and upload a map like I have, you can write Mauricio and he will give you the same modification or I can send you...
Forum: Zongshen RX3 09-20-2021, 06:06 PM
Replies: 108
Views: 11,506
Posted By Lukas
Now that the bike is running I would recommend...

Now that the bike is running I would recommend that you make a log file then if you have a problem it will be easier to see what is wrong by comparing the log file.
Forum: Zongshen RX3 09-20-2021, 06:47 AM
Replies: 108
Views: 11,506
Posted By Lukas
Some resistor has burned and as it gets...

Some resistor has burned and as it gets temperature, it expands and gives a signal it can be located you need to go from TPS along the cable to the ecu plug and check to which pins it is connected...
Forum: Zongshen RX3 09-16-2021, 06:30 PM
Replies: 108
Views: 11,506
Posted By Lukas
Warm up the motorcycle so that the problem occurs...

Warm up the motorcycle so that the problem occurs and unscrev the TPS, set it manually to zero so that the software shows it as 0% and see if the motorcycle continues to run bad with unscreved tps...
Forum: Zongshen RX3 09-16-2021, 06:24 PM
Replies: 108
Views: 11,506
Posted By Lukas
When you unscrewed the bolt, in the software what...

When you unscrewed the bolt, in the software what was the throttle position value 0?
Forum: Zongshen RX3 09-16-2021, 06:16 PM
Replies: 108
Views: 11,506
Posted By Lukas
That's why I wanted him to unscrew the TPS and...

That's why I wanted him to unscrew the TPS and warm up the motorcycle, only not to unbolt it, if the motorcycle after warming up starts to show in the hod ecu hacker that the throttle is open as it...
Forum: Zongshen RX3 09-16-2021, 01:52 PM
Replies: 108
Views: 11,506
Posted By Lukas
this screw adjust throotle position do this with...

this screw adjust throotle position do this with hud ecu hacker on to see position
Forum: Zongshen RX3 09-16-2021, 11:01 AM
Replies: 108
Views: 11,506
Posted By Lukas
The hod ecu hacker program shows that you change...

The hod ecu hacker program shows that you change the position of the throttle as the temperature increases, warm up the motorcycle and loosen the screw slightly, mark it as originally set in case of...
Forum: Zongshen RX3 09-16-2021, 08:35 AM
Replies: 108
Views: 11,506
Posted By Lukas
Before you do that you should try to adjust the...

Before you do that you should try to adjust the throttle on a warm engine with this screw then wait for it to cool down and see if it is ok.
Forum: Zongshen RX3 09-15-2021, 09:37 PM
Replies: 108
Views: 11,506
Posted By Lukas
check loose throttle cable.

check loose throttle cable.
Forum: Zongshen RX3 09-15-2021, 09:21 PM
Replies: 108
Views: 11,506
Posted By Lukas
If you unscrew it on a cold engine and manage to...

If you unscrew it on a cold engine and manage to keep it out of adjustment and it is still in the 0 position then in the software you will be able to see if the throttle position changes as the...
Forum: Zongshen RX3 09-15-2021, 09:10 PM
Replies: 108
Views: 11,506
Posted By Lukas
Charlie unscrew the TPS from the throttle, but...

Charlie unscrew the TPS from the throttle, but don't unplug the plug and see how much it shows in the program, if 0 it's a throttle problem, if above zero now it's 1.5%, it's probably a short circuit...
Forum: Zongshen RX3 09-15-2021, 08:50 PM
Replies: 108
Views: 11,506
Posted By Lukas
the position is wrong, it should be zero and it...

the position is wrong, it should be zero and it increases with the temperature change
Forum: Zongshen RX3 09-15-2021, 08:45 PM
Replies: 108
Views: 11,506
Posted By Lukas
I checked on this log file that charlie posted a...

I checked on this log file that charlie posted a dozen days ago and on it you can see that the throttle position increases as the motorcycle warms up.
Forum: Zongshen RX3 09-15-2021, 08:34 PM
Replies: 108
Views: 11,506
Posted By Lukas
This description shows that it was ok then until...

This description shows that it was ok then until it warmed up and now it was also ok until it warmed up I also looked at this log file from 20 min and the throttle position and it is 0.2% and on this...
Forum: Zongshen RX3 09-15-2021, 08:21 PM
Replies: 108
Views: 11,506
Posted By Lukas
I wonder if it adapts itself?

I wonder if it adapts itself?
Forum: Zongshen RX3 09-15-2021, 08:19 PM
Replies: 108
Views: 11,506
Posted By Lukas
From what I've been able to find out is that the...

From what I've been able to find out is that the column I've highlighted shows the number of correct passes charlie wrote that he drives a bit so that's a good indication I think if I drive mine a...
Forum: Zongshen RX3 09-15-2021, 07:37 PM
Replies: 108
Views: 11,506
Posted By Lukas
his probe works the same as mine and my bike...

his probe works the same as mine and my bike rides normally, you can see on the log that the voltage jump are identical
Forum: Zongshen RX3 09-15-2021, 07:04 PM
Replies: 108
Views: 11,506
Posted By Lukas
i know you write this but i want be sure

i know you write this but i want be sure
Forum: Zongshen RX3 09-15-2021, 06:37 PM
Replies: 108
Views: 11,506
Posted By Lukas
are you change this sensor?

are you change this sensor?
Forum: Zongshen RX3 09-15-2021, 06:26 PM
Replies: 108
Views: 11,506
Posted By Lukas
Here with ben elli TRK at 86c and your 86c I am...

Here with ben elli TRK at 86c and your 86c I am not sure if it is not the engine temp sensor that is the issue, it has a puncture I need to think about it a bit and look for info.
Forum: Zongshen RX3 09-15-2021, 06:20 PM
Replies: 108
Views: 11,506
Posted By Lukas
I compared with other log file available in hod...

I compared with other log file available in hod ecu hacker and mine, but on mine I didn't have the motorcycle warmed up like that, but on the map from ben elli there is that temperature, which is 86...
Showing results 1 to 25 of 54
Page 1 of 3 1 23

 
Forum Jump

All times are GMT -4. The time now is 02:51 PM.

Contact Us - ChinaRiders.net - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.