Forum: Zongshen RX3
08-11-2015, 10:16 AM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
06-01-2015, 10:20 AM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
05-21-2015, 05:08 PM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
05-11-2015, 03:27 PM
|
Replies: 5,437
Views: 14,241,066
Also remember that as part of a typical dealers...
Also remember that as part of a typical dealers PDI they will check these items that we are finding loose and tighten them. We are each dealing with it individually. Not the outside of public eyes...
|
Forum: Zongshen RX3
05-08-2015, 12:58 PM
|
Replies: 5,437
Views: 14,241,066
Two curves at the bottom deal with fuel.
...
Two curves at the bottom deal with fuel.
Straight upwards is amount of fuel used.
Inverse curve shows efficiency of transferring potential energy of fuel into mechanical energy.
|
Forum: Zongshen RX3
05-07-2015, 04:39 PM
|
Replies: 5,437
Views: 14,241,066
25.6hp @ 8994 rpm
This is a brake dyno of some...
25.6hp @ 8994 rpm
This is a brake dyno of some type. Easy to tell by the rpm time trace. Engine is at maximum rpm then is pulled down to lower rpm over 6 seconds. These types of dyno's are hard on...
|
Forum: Zongshen RX3
05-04-2015, 09:49 AM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
05-01-2015, 09:53 AM
|
Replies: 5,437
Views: 14,241,066
Yes a bit more involved.
Been kicking around...
Yes a bit more involved.
Been kicking around ideas with other engine builders and we tend to not include the technical details of each possibility as we are familiar with them. I responded here...
|
Forum: Zongshen RX3
04-30-2015, 08:27 AM
|
Replies: 5,437
Views: 14,241,066
There are clearances from crankshaft and rod...
There are clearances from crankshaft and rod assembly to the surrounding case. These clearances have to be maintained.
So if you have a 24mm crank pin stock and switch to a 22mm pin. Keep the...
|
Forum: Zongshen RX3
04-28-2015, 03:10 PM
|
Replies: 5,437
Views: 14,241,066
Making a stroker crank is easy. Just go to a...
Making a stroker crank is easy. Just go to a smaller crank pin diameter. However that is also a way to make it less reliable.
I will be looking for a reliable way to make a stroker crank. However...
|
Forum: Zongshen RX3
04-28-2015, 12:54 PM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
04-28-2015, 11:51 AM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
04-22-2015, 06:53 PM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
04-21-2015, 05:32 PM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
04-21-2015, 03:22 PM
|
Replies: 5,437
Views: 14,241,066
Fuel pumps need to be immersed in fuel to not...
Fuel pumps need to be immersed in fuel to not overheat and fail.
Total volume of fuel tank is not useable without damaging fuel pump.
So 4.2 gallon tank
~3.3 useable volume
~2.5 till Empty...
|
Forum: Zongshen RX3
04-21-2015, 02:50 PM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
04-21-2015, 09:09 AM
|
Replies: 5,437
Views: 14,241,066
I would look for exhaust leak.
Here are...
I would look for exhaust leak.
Here are reasons why.
Immediate wind with heat. Radiators take a while to heat up. Instant heat leads to exhaust.
Right side has three possible locations that...
|
Forum: Zongshen RX3
04-20-2015, 08:55 AM
|
Replies: 5,437
Views: 14,241,066
9.2lbs including clamp and heat shield
There...
9.2lbs including clamp and heat shield
There is a catalytic converter in the very front of the muffler. It is about 3" long and about that in diameter.
Biggest obstruction is the end tube on...
|
Forum: Zongshen RX3
04-19-2015, 05:05 PM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
04-18-2015, 05:50 PM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
04-18-2015, 02:47 PM
|
Replies: 5,437
Views: 14,241,066
|
Forum: Zongshen RX3
04-18-2015, 01:26 PM
|
Replies: 5,437
Views: 14,241,066
Initial ride report at just over 100 miles.
...
Initial ride report at just over 100 miles.
It has been a while since I was on a street bike with such low power. Power was sufficient to run 65-70 on highway two-up and keep up with flow or pass...
|
Forum: Zongshen RX3
04-18-2015, 01:13 PM
|
Replies: 5,437
Views: 14,241,066
Initial build items.
Check ALL the bolts for...
Initial build items.
Check ALL the bolts for tightness. Repeat ALL the bolts.
Check header to rear brake line clearance
Check evaporation system tube to header clearance (below battery behind main...
|
Forum: Zongshen RX3
04-18-2015, 01:01 PM
|
Replies: 5,437
Views: 14,241,066
I had 4 bikes delivered Thursday.
Have 3...
I had 4 bikes delivered Thursday.
Have 3 assembled
1 has over 100 miles so far. I will give setup and riding information later as I work the bugs out of all the assemblies.
Weights tested on...
|
Forum: Zongshen RX3
04-18-2015, 12:58 PM
|
Replies: 5,437
Views: 14,241,066
|