Forum: Pure Dirt
03-13-2011, 11:37 PM
|
|
Replies: 6
Views: 1,807
I took a piece of styrofoam and cut it into a...
I took a piece of styrofoam and cut it into a rectangular piece that fit just behind the battery and made contact with the bottom of the seat. I shaved and cut it until it just barely fit and with...
|
|
Forum: Pure Dirt
03-13-2011, 11:26 PM
|
|
Replies: 16
Views: 4,188
The carb jets can be bought at...
The carb jets can be bought at rockymountainatvmc.com, they have jets sorted by physical dimensions, only place I found that carries these jets.
|
|
Forum: Pure Dirt
03-13-2011, 11:23 PM
|
|
Replies: 8
Views: 4,561
|
|
Forum: Pure Dirt
09-21-2010, 12:40 PM
|
|
Replies: 8
Views: 1,723
The clutch must have slack in the cable to be...
The clutch must have slack in the cable to be adjusted properly. There should be 1-2mm of slack in the lever indicating the that clutch is fully engaged when you don't have your hand on the lever....
|
|
Forum: Pure Dirt
09-15-2010, 02:19 PM
|
|
Replies: 7
Views: 1,729
Your right, and I honestly apologize.
I...
Your right, and I honestly apologize.
I must have taken my a$$hole pills that morning.
Sorry bud.
You are right as well in some respects, most people aren't going to want to mess with all...
|
|
Forum: Pure Dirt
09-11-2010, 04:07 PM
|
|
Replies: 11
Views: 2,069
|
|
Forum: Pure Dirt
09-11-2010, 04:05 PM
|
|
Replies: 7
Views: 1,729
WRONG
These carbs are rich as hell from the...
WRONG
These carbs are rich as hell from the factory, sometimes lean as hell, really depends on what brand you buy.
They can always use tuning of the pilot and main and needle clip position for...
|
|
Forum: Pure Dirt
09-06-2010, 05:25 PM
|
|
Replies: 12
Views: 4,875
|
|
Forum: Pure Dirt
09-06-2010, 05:03 PM
|
|
Replies: 11
Views: 2,069
For anyone that cares;
Use MARINE grease to...
For anyone that cares;
Use MARINE grease to lube the inside of the hub inside the inner spacer for the axel bolt. This will truly repel water, as regular axel grease does so but for only a short...
|
|
Forum: Pure Dirt
08-31-2010, 12:08 PM
|
|
Replies: 11
Views: 15,657
|
|
Forum: Pure Dirt
08-29-2010, 06:23 PM
|
|
Replies: 18
Views: 3,758
Dumped 3.9L of 87 in the bike yesterday and had...
Dumped 3.9L of 87 in the bike yesterday and had it ideling fine for about 10 minutes solid. Bike was plenty warmed up and I started to give it a little bit of throttle and noticed no difference at...
|
|
Forum: Pure Dirt
08-28-2010, 08:24 PM
|
|
Replies: 7
Views: 2,553
|
|
Forum: Pure Dirt
08-28-2010, 08:21 PM
|
|
Replies: 8
Views: 1,550
|
|
Forum: Pure Dirt
08-28-2010, 08:18 PM
|
|
Replies: 18
Views: 3,758
Running a higher octane can actually hurt...
Running a higher octane can actually hurt performance because the compression on the head may not be good enough to fully ignite it.
Going to try some 87 tomorrow on it. If I hear any kind of...
|
|
Forum: Pure Dirt
08-28-2010, 08:17 PM
|
|
Replies: 6
Views: 1,894
Foster,
I saw this engine on thursday at...
Foster,
I saw this engine on thursday at the honda dealership. It is almost 100% identical in shapes, proportions etc.
It is an overhead cam engine with the exact same chain tensioner cover,...
|
|
Forum: Pure Dirt
08-26-2010, 11:01 PM
|
|
Replies: 8
Views: 1,550
|
|
Forum: Pure Dirt
08-22-2010, 04:32 PM
|
|
Replies: 1
Views: 1,165
|
|
Forum: Pure Dirt
08-21-2010, 11:09 PM
|
|
Replies: 6
Views: 1,894
|
|
Forum: Pure Dirt
08-21-2010, 11:06 PM
|
|
Replies: 17
Views: 3,313
|
|
Forum: Pure Dirt
08-12-2010, 12:20 AM
|
|
Replies: 13
Views: 3,643
|
|
Forum: Pure Dirt
08-12-2010, 12:09 AM
|
|
Replies: 18
Views: 3,758
X31 octane?
Is it necessary to run 91 octane on the 2010 x31?
The engine I thought had a compression ratio of 9:1 which I'm positive only requires 87 octane.. But I'm not sure.
I ask this because I have...
|
|
Forum: Pure Dirt
08-12-2010, 12:06 AM
|
|
Replies: 4
Views: 1,328
|
|
Forum: Pure Dirt
08-02-2010, 07:09 PM
|
|
Replies: 7
Views: 1,621
|
|
Forum: Pure Dirt
08-01-2010, 06:04 PM
|
|
Replies: 10
Views: 2,497
I couldn't rebuild my Orion forks because the...
I couldn't rebuild my Orion forks because the retaining clip for the fork seal cannot come out. It does not have any notches or bends in it like on my yz250 that allow you to 'pop' it out. I even...
|
|
Forum: Pure Dirt
08-01-2010, 05:45 PM
|
|
Replies: 14
Views: 2,127
|
