Go Back   ChinaRiders Forums > Search Forums
Register FAQ Community Calendar Today's Posts Search
Showing results 1 to 11 of 11
Search took 0.01 seconds.
Search: Posts Made By: John Phoenix
Forum: Pit/Pocket Bikes & Scooters 02-28-2023, 02:49 AM
Replies: 12
Views: 2,421
Posted By John Phoenix
Bluewing Lives! I think it runs better...

Bluewing Lives!

I think it runs better than it ran from the factory. I had no drill or grinding wheel. Trying to use a hack saw on the cone shaped breakaway plugs on the float bowl wasn't...
Forum: Pit/Pocket Bikes & Scooters 02-27-2023, 06:43 AM
Replies: 12
Views: 2,421
Posted By John Phoenix
I didn't have a drill but used an awl from a...

I didn't have a drill but used an awl from a Swiss army knife to make a pilot hole then used a screw eye to bite into and remove the plug. This worked well because I had to get pliers on the screw...
Forum: Pit/Pocket Bikes & Scooters 02-27-2023, 01:47 AM
Replies: 12
Views: 2,421
Posted By John Phoenix
There is one port on the bottom of the float bowl...

There is one port on the bottom of the float bowl next to the hose that allows you to drain the gas from the bowl that is not plugged nor had a hose on it. I assume this is on purpose? I don't see...
Forum: Pit/Pocket Bikes & Scooters 02-27-2023, 12:46 AM
Replies: 12
Views: 2,421
Posted By John Phoenix
Krat - I found this on the screws that need to be...

Krat - I found this on the screws that need to be slotted - https://www.youtube.com/watch?v=MSWWYVchEqM

Looking at my carb I do have slot-less screws that hold on the float bowl but I seem to have...
Forum: Pit/Pocket Bikes & Scooters 02-26-2023, 11:58 PM
Replies: 12
Views: 2,421
Posted By John Phoenix
Krat - I just found that out when taking off the...

Krat - I just found that out when taking off the carb. Go ahead, laugh at the newbie! LOL

"you will also need to slot the assembly screws before you can open the carb to clean or adjust...
Forum: Pit/Pocket Bikes & Scooters 02-26-2023, 03:56 AM
Replies: 12
Views: 2,421
Posted By John Phoenix
I Have to get it running tomorrow because my 2008...

I Have to get it running tomorrow because my 2008 Smart Car died. A oily ring fell out of the back engine area which I found on the street while the wife and I were pushing the car back onto the...
Forum: Pit/Pocket Bikes & Scooters 02-22-2023, 11:56 AM
Replies: 12
Views: 2,421
Posted By John Phoenix
Thanks Jerry. I have been dreading the idea of...

Thanks Jerry. I have been dreading the idea of fooling with that cus everything is so hard to reach. I'll have to pull the carb all the way off and grab some gasket sealer in case I ruin a gasket.
...
Forum: Pit/Pocket Bikes & Scooters 02-22-2023, 10:44 AM
Replies: 12
Views: 2,421
Posted By John Phoenix
Scooter runs Only after taping off air intake - How to fix?

I've pulled my hair out last couple of days trying to get my 150cc scooter to keep running after it sat for 9 months. I changed the gas, sprayed the heck out of the carb with carb cleaner, checked...
Forum: Pit/Pocket Bikes & Scooters 01-14-2022, 01:43 PM
Replies: 2
Views: 601
Posted By John Phoenix
Quality PD24J carb replacement?

Hi.

I'm looking to replace my stock PD24J carb with a quality but inexpensive unit. The scooter is a Dong Fang brand "Razor 150" sold through Redfox Powersports. I see Amazon in the USA has them...
Forum: Dealer & Distributor Discussion 05-22-2021, 10:56 PM
Replies: 13
Views: 3,458
Posted By John Phoenix
I just bought a 150cc scooter "Razor 150" from...

I just bought a 150cc scooter "Razor 150" from RedFoxPowerSports in California and they shipped it to New Orleans. I was nervous as hell. I read a Ton of bad reviews on them as well as spoke to a few...
Forum: New Member Introductions 05-22-2021, 10:05 PM
Replies: 2
Views: 684
Posted By John Phoenix
Hello from New Orleans

:yay: Greetings gents, ladies and those who are unsure. I'm John from New Orleans New to riding. Just got my first gas operated 150cc China scooter. 5 minutes later.. Just wrecked my first gas...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -4. The time now is 10:21 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.