ChinaRiders Forums

ChinaRiders Forums (http://www.chinariders.net/index.php)
-   Parts & Accessories (http://www.chinariders.net/forumdisplay.php?f=105)
-   -   LOTS of LIFAN GY-5 parts AND motor parts (http://www.chinariders.net/showthread.php?t=12431)

Wild_Alaskan 05-07-2013 09:21 PM

LOTS of LIFAN GY-5 parts AND motor parts
 
Everything you see here as well as a front wheel and a COMPLETE PARTS MOTOR (167FML pushrod version) I can pick parts off of as needed. I may have other parts that are not visible in the photo, PM for condition of parts or better photos I'm letting them go cheap to those in need. :wink:

http://i1154.photobucket.com/albums/...psaef434b1.jpg

Weldangrind 05-08-2013 01:26 AM

Shipping from AK or MT? I'd be interested in the pushrod motor, but shipping might be prohibitively expensive for me.

Weldangrind 05-08-2013 01:27 AM

Do you have a good set of plastic side covers? Got a close-up pic of them?

Wild_Alaskan 05-08-2013 01:55 AM

http://i1154.photobucket.com/albums/...ps4f2f809a.jpg

http://i1154.photobucket.com/albums/...ps9dd54f34.jpg

The upper white one has a little crack below the rear screw hole and was damaged by a forklift when it was being unloaded from the barge

http://i1154.photobucket.com/albums/...psd2ddad14.jpg

Shipping is from alaska so the entire motor would probably not be possible, I think the valves and bore have been damaged from getting stored out side anyways

Weldangrind 05-08-2013 02:03 AM

I think that those would require more fab work than the GY150 covers I already bought. Is the tank plastic? Got a pic?

Wild_Alaskan 05-08-2013 02:18 AM

I am planing on using the gas tank for the buggy project actually

Weldangrind 05-08-2013 10:06 AM

Ok, thanks anyway. I can't think of anything else I can use.

edtardo 05-09-2013 06:05 PM

How much would you let the motor go for?

Wild_Alaskan 05-09-2013 10:16 PM

The motor has a bad top end from sitting out side and shipping from alaska would be $100+

NewEnglandTrails 05-26-2013 07:47 AM

I'd be interested in the front headlight housing if its still around... I have a Roketa db 05 and the housing is cracked in two. I see it in your o.p. but barely. Any chance on a front and back photo..?

bogieboy 05-26-2013 09:05 AM

Is the harness i spy complete? If so how much shipped to 60473? Thanks!

edtardo 05-26-2013 11:24 AM

I think that is a polisport mmx headlight

Wild_Alaskan 05-26-2013 01:19 PM

Quote:

Originally Posted by NewEnglandTrails (Post 152464)
I'd be interested in the front headlight housing if its still around... I have a Roketa db 05 and the housing is cracked in two. I see it in your o.p. but barely. Any chance on a front and back photo..?

Hi it isnt a stock headlight it is a polisport as edtardo said. I will mount up to the stock mount on a gy-5 through the two upper holes. I never made a bracket for securing it better because it really didnt end up needing one. It is wired in to a plug for the gy-5.

Quote:

Originally Posted by bogieboy (Post 152466)
Is the harness i spy complete? If so how much shipped to 60473? Thanks!

I will have to double check but i believe it is complete except for the engine plug has been converted to bullet connectors because I was using it on my 400cc motor conversion. It would be pretty easy to convert back to the stock plug.

my first wiring harness failed and it took over a year of searching to find one that would work because they changed the wiring harness between years and countrys that the bikes were shipped to ( still had to change the turn signal wires on the bike to match this one). if you would like I can take pictures of all the connectors and you can compare it to yours.

bogieboy 05-26-2013 01:22 PM

Quote:

Originally Posted by Wild_Alaskan (Post 152476)
Hi it isnt a stock headlight it is a polisport as edtardo said. I will mount up to the stock mount on a gy-5 through the two upper holes. I never made a bracket for securing it better because it really didnt end up needing one. It is wired in to a plug for the gy-5.


I will have to double check but i believe it is complete except for the engine plug has been converted to bullet connectors because I was using it on my 400cc motor conversion. It would be pretty easy to convert back to the stock plug.

my first wiring harness failed and it took over a year of searching to find one that would work because they changed the wiring harness between years and countrys that the bikes were shipped to ( still had to change the turn signal wires on the bike to match this one). if you would like I can take pictures of all the connectors and you can compare it to yours.

i wont have the bike in my hands till saturday...LOL,i am know it needs a new harness, as the PO hacked it all up...at least he admits it...LOL
ifplugs dont match up thats not thebiggest issue forme to dealwith...LOLilike bullet connectors...easier to crimp than the stupid molex plug style....although i have acess to those too....LOL

nyvdub89 06-08-2013 01:49 PM

Hello Wild_Alaskan I was wondering if you had the throttle grip assembly for sale? I also need the choke cable, headlight plastic, and front brake booster if you have it available. Thanks man!


All times are GMT -4. The time now is 06:59 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.