Zongshen RX3 Parts Cross Reference: Please Contribute!
 

Spud

All these brake pads, rotors, foot pegs, foot pedals, windshields, etc.
So many forums these things are scattered about, it would be nice to have them in one place in one list.

Could you start a sticky of parts cross ref. that all could contribute to.

:thanks:

Oil filter is there just the CSC filters or is there another source??

ZS177MM / NC250 Clutch crossreference = Honda dominator 650 , NX 650 EBC CK1170 series dimensions bit tight tolarance 0.01-2mm , same, i used that on my ZS177MM / NC250 confirmed


Note : originals better , only use if cant find original clutchs, just instead exigency (on travel need repair or...)

I think this thread is an excellent start for that project, Keith. :tup: I am pinning this thread to the top of this forum. :) As members contribute equivalent parts to this thread, I will compile an organized list of parts. I will place that organized list in a closed thread, which I will also pin to the top of this forum. :)

Spud

your simply awesome :thanks:

Thank you, Sir! :tup:

I always suspected the RX3 clutch parts were Honda parts. ;) Here is a list of the Honda motorcycles which employ the same friction plates, fiber plates, and clutch springs as the Zongshen RX3.

Honda XR650L
Honda XR600R
Honda NX650
Honda CR500R
Honda CR480R
Honda CR250R

A lot of people like the Tusk Clutch Kits you can purchase from Rocky Mountain ATV/MC. :)

https://www.rockymountainatvmc.com/p...ch-Kit?v=11638

https://images.rockymountainatvmc.co...clutch_kit.jpg

Until someone discovers otherwise, I don't know of another oil filter which fits the ZS177MM/NC250 engine of the Zongshen RX3. :shrug:

However, I purchase stainless steel, reusable oil filters for my RX3 from Taobao. They do an excellent job protecting the engine, and are much less expensive than replacing paper oil filters. ;)

https://item.taobao.com/item.htm?spm...cket=10#detail

https://gd4.alicdn.com/bao/uploaded/...0-item_pic.jpg

However, I wouldn't be surprised if a BMW or KTM motorcycle employs these oil filters. ;)

Thank you for coming up with the great idea, Keith. :tup:

Thank you for listening, I find this forum to be one of the best forums I have ever been part of.

It is members such as you who make these forums such a great place to frequent. :)

I have posted a thread with confirmed parts which fit the Zongshen RX3. This closed thread is pinned to the top of this forum, at the following link.

http://www.chinariders.net/showthread.php?t=15532

Please post your confirmed parts in this thread, and I will add those parts to the closed list. :) If I forget to add any items to the closed list, please don't hesitate to inform me in this thread. ;) Thank you.

:thanks:

Great idea ... thanks Keith and Spud!

How about the accessory plug connectors? The are the ones under the seat, right?

http://www.chinariders.net/showpost....9&postcount=26

Awesome input all the way around

Thanks for the input. :tup: Indeed, I will add those connectors to the list. I also know the connectors for the headlight, and the ECU diagnostic port. ;)

This is such a cool shop to hang out in. :tup:

You're welcome , but i warn, on link and photo " metal disk's " i no idea im just use nx650 dominator clutch plates , friction metal discs i use old originals, and seeing photos metal discs i think much bold.

Here my old acc, on forum mt, search and dimensions maybe have idea, again

http://www.motosiklet.net/forum/mt-a...-tip-uyum.html

EBC CK 1170 clutch's is very tight tolarance but ok worked.

Are the Honda, clutch fiber plates the same thickness as the RX3, clutch fiber plates? If you have the opportunity, please also measure the thickness of the RX3, clutch metal plates.

When I have time, I will also check the dimensions of the clutch plates in my Honda CRF250X.

Terminology mixed , my Tarzan style :lmao:

Organic/Fiber plate is ok , butif u add link on photos metal friction metal plates impossible, not need measured, many time i assemb/dissasemb clutch , if photo correct any a optical game " F " optic playing idk, but im think on photos that metal discs impossible mounted rx3 or zs177 or nc250

Measured sorry, motor block is complete , but if wait me 2-3 day later maybe, i promise.

116 mm ( in chamber , non tooth.) , 9 mm(in circle to out walls non toth) , 136 mm (out chamber) Dimensions of the metal plate.

Edit for measurement for Spud, bestregards.

Sorry bad Photos by sj1000 (because my suck xperia u phone probably today REGL/menstruation
, %+&%+/% waste phone never buy.)

Nx 650 dominator Fiber/organic idk, clutchs on my zs177mm, i used it 500 kilometer than, non problem, just mounted very tight tolaration, thick but worked i cant feel any problem it worked.

Edit 2 sj1000 need setup for date and watch. , photos is fresh 10 min ago.

http://i.hizliresim.com/PBjn85.jpg

http://i.hizliresim.com/p9OXyr.jpg

http://i.hizliresim.com/ZJlM8G.jpg
http://hizliresim.com/PBjn85

Okay. The Honda, fiber clutch plates are okay, but the metal clutch plates are too thick.

When you have time, please do measure the thickness of the metal clutch plates in your engine. Also, please measure the thickness of the Honda, fiber clutch plates. We are happy to wait. Take your time, we are not in a hurry. ;)

116 mm ( in chamber , non tooth.) , 9 mm(in circle to out walls non toth) , 136 mm (out chamber) Dimensions of the metal plate.

http://hizliresim.com/4LQO6Ahttp://hizliresim.com/4LQO6Ahttp://hizliresim.com/4LQO6A

Metal and clutch original fiber same dimensions.. , nx 650 clutch bit bigger..... but worked.

http://i.hizliresim.com/n24ljg.jpg

Right is original, left is Honda nx 650 dominator EBC ck1170

Diff is original end Honda clutch.

Original chamber in : 117 milimeter.

Original out of chamber (not teths/tooths.) : 136 milimeter

Original out and in chamber wall (not teths/toots.) : 9 milimeter

-------------------------------------------------------------------------

Honda dominator clutch chamber in : 116 milimeter


Honda dominator out of chamber(not teths/tooths.) : 138 milimeter

Honda dominator out and in chamber wall (not teths/toots.) : 11 milimeter.


My moto in " METAL PLATE " Dimensions same to original clutch plate 1-1 same dimens..

İ hope now ok.

Thank you. I saw those measurements in your last post. :)

When it is convenient, please measure the thickness of the metal clutch plates, and the thickness of the Honda, fiber clutch plates. ;)

thickness Honda dominator clutch fiber/organic idk = 3 milimeter

thickness original friction/clutch metal plate = 1 milimeter.

Thank you, Sir. :)

so this guy got bored and painted his RX3 to resemble a GS

What I want to know is what adjustable clutch and brake levers did he use? What levers are compatible? I would like adjustable Chinese machined levers please

https://www.facebook.com/photo.php?f...type=3&theater

I don't know for certain, but I think he probably switched the clutch perch, and likely switched the clutch cable as well. Did he change the brake lever, also? I don't frequent Facebook, and I only see the one photograph. ;)

I'm assuming it's the stock perch. Most adjustable levers sold are for stock perch.
We just need to know which bike's lever is a match

like these
http://www.ebay.com/itm/Short-CNC-Ad...hU9rUz&vxp=mtr

Yes, I understand. However, based upon my past experience with Chinese bikes, I'm guessing he is not using the stock perch. However, I hope I'm wrong.

Is he an active member over there? Can you ask him that question on Facebook? I really don't know much about Facebook. ;)

That would be great if those would fit :tup:

he very well may have done like i did... i went new perches and all on my roketa.... cant argue with $45 from ebay...

http://i.ebayimg.com/images/i/271765...0-0/s-l140.jpg

like these perhaps

http://www.ebay.com/itm/7-8-22mm-Bra...FVn3mz&vxp=mtr

http://i.ebayimg.com/images/g/AS0AAO...3mz/s-l500.jpg

or these
http://www.ebay.com/itm/Gold-7-8-Bra...tV9QLF&vxp=mtr

The HiFlow filter website lists the dimensions of all their oil filters. If anyone wishes to search the catalog, he might be able to find an equivalent oil filter for the RX3. ;)

http://www.hiflofiltro.com/catalogue

http://www.hiflofiltro.com/fileadmin...arge/HF652.png

The people at CSC are always very helpful. :tup: I just talked to Gerry in the service department, and he told me the thread for the radiator fan switch is 16 mm in diameter. These switches will occasionally fail, so It's good to have a spare switch on hand. However, these switches are always sold with the complete radiator, rather than alone. ;)

I believe the following, radiator fan switch is equivalent to the switch employed by the Zongshen RX3. It is a switch designed for the following Suzuki and Kawasaki motorcycles.

Suzuki

GSX-R600 97-05
GSX-R750 96-08
VL/VZ800 01-11
DL1000 V-Strom 03-09
GSX-R1000 01-04
SV1000 03-07
TL1000R/S 98-03
GSX-R1300 “Hayabusa” 99-07

Kawasaki

Ninja ZX-6R 2003-2004
ZX636 2003-2004
ZX600 2003-2004

http://www.ebay.com/sch/i.html?_from...witch&_sacat=0

http://img.jpcycles.com/zoom/ZZ34359_A.jpg

http://ecx.images-amazon.com/images/I/41Ow2c-Qf9L.jpg

Does the connector look the same to you, Spud?

Yes it does. :) Here are some photos of the connector from the CSC website.

http://www.cscmotorcycles.com/v/vspf...ge_%20(11).jpg

http://www.cscmotorcycles.com/v/vspf...ge_%20(12).jpg

It seems the Delphi 28086011, Delco 12232201 MAP sensor is equivalent to the MAP/MAT sensor of the Zongshen RX3. Just make sure you get a 4-pin connector (MAT). It's best if the sensor has a sticker which labels the 4 pins: VOut, 5V, MAT, GND.

http://www.ebay.com/sch/sis.html?_nk...p2047675.m4096

http://image4.pushauction.com/350/35...d6049265cc.jpg

It seems the solenoid purge valve for the evaporative emissions canister is the Delphi 1997278, ACDelco 214-641 unit. :)

http://www.ebay.com/itm/Evaporative-...3D130848197922

http://d3d71ba2asa5oz.cloudfront.net...5890_400_4.jpg

Stock front brake pad IS CD-F544 http://www.chinamomt.com/product1.php?page=19#
A：94.2×33.2×8 | B：94.2×33.2×8
http://i04.c.aliimg.com/img/ibank/20...0_99789240.jpg

You guys are awesome. Thanks for all the research finding compatible parts!